Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Bandsaw maintenance question

Posts

Bandsaw maintenance question

#1

Bandsaw maintenance question

Jesse Cloud

>The bearings on my bandsaw, particularly the lower ones, take a lot of abuse. Though I clean the saw after each use and blow it out with compressed air frequently, the lower bearings often get clogged and sticky. Some quality time with a can of WD-20 and an old toothbrush brings them back to life, but I'm wondering if I am neglecting some needed maintenance. Do you lube your bearings? The manual has nothing to say on the subject.

Thanks in advance.

Jess

Re: Bandsaw maintenance question

#2

Re: Bandsaw maintenance question

Lewis Dodd

>Well, the answer could be you are using half strength WD lubricant! (;>Q)))

Lewis

Re: Bandsaw maintenance question

#3

Re: Bandsaw maintenance question

chuck

>aren't the bearings sealed against dust and dirt? do they need to be cleaned?

Re: Bandsaw maintenance question

#4

Stop!

Bill Tindall, E.TN

>You did not say what kind of saw this is but in most cases bearings are sealed and require no attention until they fail. All the diddling that you are doing to them at best does nothing helpful and at worse the WD 40 may be attacking the seal. I haven't looked at mine in 30 years. Indeed, they are likely dusty.

Re: Bandsaw maintenance question

#5

I think the WD-40 may be a mistake

Grant in Iowa

>If the bearings aren't truly sealed, I'm betting WD-40 may be getting past the shield or seal and may be diluting the lube inside the bearing.

That, and the WD stays around to attract more dust later on.

Also make sure they are adjusted correctly, they shouldn't spin unless you are engaging a workpiece.

Regards,

Grant in Iowa

Re: Bandsaw maintenance question

#6

Re: Bandsaw bearing problem - two suggestions

North of the Border

>1) As others have pointed out, if the bearing is sealed, check if WD 40 is the right product to use. A dry lubricant which do not attract dust may be a more suitable alternative.

2) Do you use duct collection for your bandsaw? I haven't encountered the problem you reported and wonder if my use of dust collection might be part of the reason.

Re: Bandsaw maintenance question

#7

Re: Bandsaw bearing problem - two suggestions

John Lucas

>WD-40 is not a lubricant. When I worked in electronic and camera repair I saw more things damaged using this stuff. It gums up the works after a short period and actually does the opposite of lubricating. It could also damage the seals as others have said.

If you lubricate them at all use a good oil. I use LPS 2 on mine and it seems to help. My bearings are really old but it works for a while.

Re: Bandsaw maintenance question

#8

Yeah, adding lube is not always good...

John in NM

>I just replaced the bearings in my Foredom motor, they were loaded with dust and I thought beginning to get a bit hot. After wiping them off and adding some 3 in 1 they started getting much more noisy and after a few weeks I couldn't stand it and replaced them. Sealed bearings are designed to use the lube that's behind the seal, a lightish grease. I wouldn't worry about breaking down the seal or anything like that - seal is a very optimistic name in a dusty environment - but light oils will thin the grease in the bearing and probably shorten its life (unless you oil it before every use after the grease is gone).

But the good news is bearings are pretty cheep, and bandsaw guides are one place where they are extremely easy to replace. If you need replacements they are fairly easy to find in most cities, I know of one in Albuquerque (there are probably several) near I-25, on one of those streets named for colleges... can't remember which one, but I bet my wife will if I ask.

Re: Bandsaw maintenance question

#9

Re: Bandsaw maintenance question

ThomD

>WD40 is the 40th water displacement oil formula the company came up with when trying to meet a contract. As all have said, no place in bearings. Bearings are either sealed, in which case you will see two rings of metal with a plate between them (the dust shield). In theory that shield is there to stop the grease from exiting under fan pressure, not so much to stop stuff getting in. This is one of those political arguments in the bike field where people put stock in sealed bearings to keep water out. Anywho, the other option is they are serviceable, repackable, greaseable. These could have grease cups, or zirc fittings for the grease. Or some obvious means of accessing them, even if the required wrench is unusual. There are also plain bearing, just a shaft in some kind of metal, these required the correct oil to be used constantly.

Sometimes a new machine will have bearing problems fairly directly, if the sealed bearings used are junk. Bearing replacement may get you a machine good for a 100 years.

Re: Bandsaw maintenance question

#10

Sounds like time for new bearings...

Jesse Cloud

>Thanks all. Great input. Sounds like I need new bearings. It is, indeed, a fairly new bandsaw and I'll bet the bearings are junk.

John, if you don't mind, please ask your wife if she can remember where to buy bearings in Albuquerque.

Thanks,

Jess

Re: Bandsaw maintenance question

#11

Yes, Stop! Compressed air is a no-no

Forrest Addy

>Yes, Stop! Compressed air is a no-no around workng parts. If you need to clean up use a bruch and a shop vac. Air will blow crap into spazes viruses can't access.

WD40 is an excellent cleaner of single parts or small assembles havng no movng parts within them. It is te world poorest lubricant. For one thing applying it with a pray washes debris into crevces. For another it slowly evaporates. For another it'smostly kerosene. It doesn' form a srong hydrodynamic film like oil. It doe attract dust and debris and sticks it together into a gooy mass.

Clean up you mess. If your bandsaw is old and has plain bearngs apply oil in the oil cup. If it has ball bearngs and they run noisy, you may need to replace them. This is basic mecanic's work. Find a mentor if you need to. It aint rocket science.

Re: Bandsaw maintenance question

#12

Re: Sounds like time for new bearings...

Rick in Colgate, Wi

>The bearings on my Grizzly G0555 died fairly quickly. Turns out the bearings they use were the same that are commonly used in roller blades. Found an old pair at a rummage and now have replacement bearings for years to come. The bearings are commonly found at sportings goods stores as well. I would pull a bearing, google the number on it and see what turns up.

Re: Bandsaw maintenance question

#13

Motion Industries...

John in NM

>3208 Vassar Dr NE, Albuquerque, its east of 25 about a block north of Candelaria. I could drive right to it, but never can remember the name or address for more than about a week. Go figure.

I think I picked them out because we were always over in that area at the time - there's a roofing supplier on Comanche that I preferred to use.

I was buying bearings for my RO sander that time, the Foredom ones I got down in Las Cruces on my way back from AZ. Turns out the Foredom bearings are one of the most common around - they're used in skateboard wheels so you can find them in almost any sporting goods store (so I hear - I found a bearing/hydraulic supplier instead). Probably the same ones that are in the roller blades too!

Re: Bandsaw maintenance question

#14

WD = water displacement..

Frank on Chestnut Hil

>

Re: Bandsaw maintenance question

#15

Re: I know it is

Brian in Brighton

>Everyone, repeat after me.

"WD-40 IS NOT A BEARING LUBRICANT.

It removes grease, it does not replace it."

Say that 40 times and let it sink in. Just past the seals, to ruin your lubrication.

You probably get to look forward to removing and repacking your bearings. The good news is that bearings can be pretty cheap to buy, but you might have some issues replacing them. Look at the archives, I'm sure someone has posted and article on it at some time.

Brian in Brighton