Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Tapering table legs

Posts

Tapering table legs

#1

Tapering table legs

Tom Pilsbury (Chicago)

>I'm building a small end table. Dimensions are (approx) 31" tall, 18"square top, 4 1/2" aprons, 1 1/2" square legs. I sandwiched (2) 3/4" boards to make the legs. Ugly as sin. Next time I'll buy thicker lumber. Anyway the square legs are kind of clunky so I want to taper them. But I don't know where to begin the taper. Should I start right at the apron or leave a few inches before the taper begins? And tapers are done on the 2 inside faces of the legs, am I right?

Re: Tapering table legs

#2

Re: Tapering table legs

Virgil Johnson

>Start the taper below the aprons as you will never get the taper to start evenly in the same spot. If you leave flat area the error won't show up. That has been my experience.Then again maybe I'm not very good. Yes taper the two inside surfaces.

Re: Tapering table legs

#3

Re: Tapering table legs

John Pappas

>Tapering inside is probably the normal, but I have seen it, and done it, on the outside.

Re: Tapering table legs

#4

Re: Tapering table legs

Barry Irby

>I agree with Virgil. I usually taper legs on the TS and shoot for the taper starting about an inch below the apron. That way you can sand them and trim them and not be concerned about leaving the top too short. I like to taper the inner two sides, but you can do all four.

Next time you end up with 3/4 stock, you can rip a 45 on each and glue them up at a right angle. This is just two pieces, an "L". Then taper the inner two edges/faces. That leaves a "rabbet" up the inside of the legs, but it might be less unsightly than just face gluing them. I had some walnut that my grandfather cut before I was born and it was only 5/8" thick. I made a small table that way and I like it. Made nice legs out of crappy but sentimental walnut.

Re: Tapering table legs

#5

JL

Re: Tapering table legs

JL

>I built a planer sled for tapering a while back. I have about a 3 degree or so incline on it. I tape the legs to the sled using double stick carpet tape. I draw a line about 2-3" below where the apron will be. I plane off wood until I start approaching the line. I give the profile a quick look-see to see if it looks reasonable. When it does, I peel the legs off of the sled, rotate 90 degrees and start again.

It is SLOWER than the table saw method. It does work though and you can sneak up on a taper and stop it when it looks good to you.

Re: Tapering table legs

#6

agree

Bill Tindall, E.TN

>Look in furniture books. A tapered leg is a popular style and you will be able to find one in a picture

Re: Tapering table legs

#7

Re: Tapering table legs

Tom Pilsbury (Chicago)

>Thanks for the advice all. I'll continue working on monday.

Re: Tapering table legs

#8

Blue tape is your friend here

Jesse Cloud

>Good advice above. But beyond the wisdom of not even trying to make the taper end consistently at the aprons (don't even think about it), where the taper is located is wholly a matter of taste.

Dry fit the table with clamps but no glue, then run a line of blue tape down the leg where the taper might go so that the part that is cut off will be covered by the tape. This will give you an idea of what that taper would look like. If not happy, take the tape off and try another location. Repeat as necessary.

Re: Tapering table legs

#9

Also Agree

George@Colonel's Workshop-Havertown PA

>

Re: Tapering table legs

#10

Ugly As Sin

George@Colonel's Workshop-Havertown PA

>Hello Tom,

I often sandwich 3/4" stock to make leg blanks. However, I rip a little off the glue-line faces of the leg, and apply veneer obtained thru re-saw. Leg edge chamfer or bead detail visually hides the veneer glue lines.

George

Re: Tapering table legs

#11

Re: Tapering table legs *LINK*

Fred Davis

>Tom ,

tapering legs is not one way only , check this table which is a ribbon winner one of two matched Mahogany hall tables I made and you will note the legs are evenly tapered on all sides starting directly below the Apron.

FredD


http://picasaweb.google.com/lh/photo/M3HVLGUQR8fDtI5QvV8cMQ?feat=directlink

Re: Tapering table legs

#12

I'll bet your Mother gave you that Ribbon....

Barry Irby

>Sorry couldn't help it, it's a family thing. Took the kids to a Four Star restaurant. It was a miserable experience for the one who is not an adventurous eater. (He was on the "Chicken Strips Tour of the South") As we left the restaurant his comment was "I bet their mother gave them those stars".

Its a beautiful table and I wish I could do so well. That style of leg calls for the four sided taper.

I have trouble convincing myself to taper them enough. Mine sometimes end up looking fat.