Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

23 gauge pin nailer

Posts

23 gauge pin nailer

#1

23 gauge pin nailer

Carol Reed - home in Strawberry

>Got a big custom job to do. A 23 gauge pin nailer would make good sense on this job.

Comments from users are appreciated. Which brand did you get? Which one would you buy now? Other information that would be helpful? What did you wish you had known when you got your gun?

Re: 23 gauge pin nailer

#2

Re: 23 gauge pin nailer

Doug Ridley

>Carol, I bought one from HF for about $25 to use on one job. It worked fine and I have used it several times since. I am not a fan of HF but if you want it for one job only it is a good deal. If it will be used a lot in the future it would probably make more sense to go with a higher priced one like a Senco or etc.

Re: 23 gauge pin nailer

#3

Re: 23 gauge pin nailer

Jim Dillon

>Carol,

Several years ago when they were discontinuing the Accuset brand (lower priced Senco), I couldn't resist a pin nailer sale as they were almost giving them away. It has been great so, if I were shopping today, I would look at the highly regarded Senco line - although more expensive. I'm assuming here that Senco still makes a pin nailer. BTW, I have also have Accuset finish, brad. and staple nailers and they all have been superb. Too bad they discontinued the line.

Jim

Re: 23 gauge pin nailer

#4

Grex...

Terry Alexander

>...It's pretty pricy...but I love it. The only problem (kinda) that you will find is that 23ga pins are pricey! You'd think those gold colored pins were actually coated in gold.

HTH

Terry Alexander in West Texas

Re: 23 gauge pin nailer

#5

Re: 23 gauge pin nailer

del schisler

>Here is the one i have and it work's great Porter-Cable PIN100 1/2-Inch to 1-Inch 23-Gauge Pin I didn't read the other post's their may be the same post

Re: 23 gauge pin nailer

#6

Bart Goldberg

Agree with the Grex choice

Bart Goldberg

>

Re: 23 gauge pin nailer

#7

Grex over Senco IMHO

Yonak

>I started with a Senco but it had this air lock problem where I had to keep disconnecting the air hose -- a pain in the neck -- and sometimes I had to do it repeatedly before the gun would work again.

I bought a Grex two years ago and have been very pleased with it.

Re: 23 gauge pin nailer

#9

A.J. Hamler

Re: 23 gauge pin nailer

A.J. Hamler

>I have the same P-C pin nailer that Del has, and I couldn't be more pleased. If you've never used a pin nailer before, you'll be surprised at just how light and maneuverable one is. They're a joy to use.

Keep in mind one safety thing about them, though. All the pinners I've seen, including mine, do not use the typical push-in safety on the nose that prevents firing until the tip is depressed against the workpiece. Because pinners are typically used on delicate work, pressing the nosepiece into the work could damage it. Instead, they use a safety located right behind the trigger. Firing a pinner is a two-step process. You first flip the safety aside, then pull the trigger.

This is simple to do while working, but once you've flipped the safety aside you have to remember that your gun is live -- you can shoot a pin across the room. It's the only kind of nailer I've seen that works this way. It's not dangerous, per se, but you have to pay attention to what you're doing.

A.J.

Re: 23 gauge pin nailer

#10

Re: 23 gauge pin nailer

George@Colonel's Workshop-Havertown PA

>Good Morning Carol,

I had used a HF pinner until my #3 son gave me his Accuset. The Accuset was more comfortable to use, but would only fire a half stickof pins. I gave it away and continued with the HF. They are inexpensive and reliable. Further, the HF pins work perfectly and are much less costly. I also appreciate that the HF leaves no footprint when it fires a pin. I have no desire to replace it with a more expensive tool, given its perfect performance.

George

Re: 23 gauge pin nailer

#11

Jim DeLaney, Austintown, Ohio

Re: 23 gauge pin nailer

Jim DeLaney, Austintown, Ohio

>My Senco shoots pins up to 1". I've never needed a longer one. About $140.00.

If you're looking for a real bargain, check out Harbor Freight. They had one for about thirty bucks a while back, and reports on it were actually pretty good.

Jim D.

Re: 23 gauge pin nailer

#12

also like the (departed) Accuset

Simon St.Laurent - Dryden, NY

>I hadn't realized they were discontinuing them when I bought mine, but it's held up well. Sadly not an option any more.

Re: 23 gauge pin nailer

#13

Rick L

Re: Most important point ignored...

Rick L

>23 Ga pins can be from 3/8" to 2"! What are your needs and what is your budget????

Up to 1" you can get HF and up for $20 and up. Over 1" the options are fewer and more expensive. This is the point of seperation for 23 ga. pinners and the topic should be addressed accordingly!!!

Re: 23 gauge pin nailer

#14

Different experience with SENCO

Hank Knight

>Jim,

I have two Accuset brad nailers and I have been very happy with them. I bought a SENCO 23 ga pinner for the same reason you did. My pinner, however, leaves the pins proud of the work surface. I cannot find any way to adjust it, so I have tossed it aside and forgotten it. One of these days I'll get around to unloading it and buying a Grex.

Hank

Re: 23 gauge pin nailer

#15

Rick L

Re: Pins sticking up...

Rick L

>Shave some off the rubber bumper. It willl allow the driver to set the pins deeper. Also if o-rings get worn wrap some dental floss around the groove and reinstall the o-ring.

Re: 23 gauge pin nailer

#16

Re: Most important point ignored...

Carol Reed - home in Strawberry

>First reason is for crown molding. Other uses will pop up. I am inclined to buy decent tools as opposed to buying throw-aways and then spending more money. If its worth owning, then I spend enough that if I no longer have a need, the tool has some resale value.

I have 18 gauge nailers but the entrance hole is unacceptably large for this job. With the 23 gauge I might do more "nail it until the glue dries" building. Ala Norm.

So far the vote leans toward the Grex, but $300? Maybe I'll look harder at the 635 or the 645. Not as many bells and whistles as the 650.

The local tool store sells Senco's, but the only vote for them was for the older models.

The reviews on the PC's are mixed, sort of a love/hate relationship.

Pawn shop as sources has come up, especially in this tough economic time, but I don't know enough about brands/models to know what I should be looking for.

Re: 23 gauge pin nailer

#17

Re: Most important point ignored...

NickB

>I have the Cadex that goes to 1 3/8" - fantastic tool and absolutely the bees' knees for quickly assembling self returns for base and crown (also great for attaching small stain-grade trim that doesn't see any load). At the time I bought (~4 yrs. ago), it didn't seem that there was any significant difference between the Grex and the Cadex in terms of performance, and I liked the little built in air gun on the Cadex.

I thought about getting the Cadex that goes to 2", but I think if you need a 2" fastener, you need something heavier than a 23 ga pin. I've been happy about the ability to go above 1", though.

Hope this helps,

Nick

Re: 23 gauge pin nailer

#18

Lets not forget the holes too!

Tony - Memphis

>I never owned any brad nailers until recently. I thought they would be nice to have for making jigs. I thought I would get better alignment by holding and pinning than I did by drilling holes for screws. Something always moves while drilling and screwing. Anyway, I got the PC kit. I bought the pin nailer later. It works fine, but I am a little dissapointed with the holes that it leaves. I don't use it for furniture projects much for that reason. Unlike Norm, I don't like little holes everywhere. I can minimize thedamage by playing with the air pressure and the depth setting. I always shoot a few into a scrap before I use it on the real thing. My guns receive very minimal usage, so I can't really report on long term durability. Mine have worked just fine so far. Sure nice to have for quick and dirty. I built a stand out of 2x4's to set my recent project to the right height for working on and that was rally handy and quick. The little PC compressor is nice. Doesn't use up too much space in my little shop either. It is LOUD! But I wear ear plugs anyway, so I don't mind.

Tony

Re: 23 gauge pin nailer

#19

Thanks for the tips

Hank Knight

>

Re: 23 gauge pin nailer

#20

Re:Reviews...Cadex looks real good.

Rick L------WebKitFormBoundaryaqNirg4xL+4nv0Cx

>I bought a cheap gun that shoots up to 1-3/16 pins but I will spring for the Cadex when I need more capacity. It shoots a headless pin and headed pin. If you need the 2" capacity you will need to spend the money. Have the Grex 1-1/2" in our commercial shop and are happy with it.

http://www.toolsnob.com/archives/2007/10/cadex_cpb2350_23_gauge_pinner_1.php

http://www.toolsofthetrade.net/industry-news.asp?articleID=536624§ionID=1491

Re: 23 gauge pin nailer

#21

Another vote for Grex

J D Thomas

>I started with the PC and it was fine, but there were times I needed to shoot longer pins. Grex is/was the only game in town then. Definitely pricey, but I've been most pleased.

I got it via Hartville in a package deal that included a boatload of pins that should last quite a while.

J D Thomas

ThomaStudios