Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Electrical Quirk question

Posts

Electrical Quirk question

#1

Electrical Quirk question

Nat Robison

>I replaced a switch and outlet next to a bathroom vanity this summer....the switch controls a light fixture over the vanity. I went to turn it on the other day and I think the lights came on for a fraction of a second and then went out. I figured that all 3 bulbs wouldn't blow at the same time (I checked with another bulb) and figured maybe the switch was faulty.....rest of the circuit was fine, it didn't trip the breaker.

Before I could check anything out in the box today, the switch works again. Anything to be concerned about or check on??

Re: Electrical Quirk question

#2

JL

Yes.

JL

>Switches can and do go bad. I have seen some switches short out. It just takes a little time to turn off the breaker, pull the wall plate off and give it a sniff. Most switches are inexpensive. If you still have the receipt....

Re: Electrical Quirk question

#3

Re: Yes. Also

Dustmaker Mike

>check connections on the light fixture and switch. If one is loose it will cause all kinds of problems and is dangerous.

Re: Electrical Quirk question

#4

Re: Electrical Quirk question

Dave Anderson (PacNW)

>I had the same Problem and found that the bath circuit was on a GFI that was in the garage. Code has required GFI's on all bath circuits for 30 years.

Dave (PacNW)

Re: Electrical Quirk question

#5

Re: Electrical Quirk question

del schisler

>probly not the GFI they trip and have to be reset He didn't say anything about a reset I would just change the switch first Check the wires in the back If they are the push in kind I wouln't use those my self Use the old screw type that has been around for long yr's ago i would look at the hook up at the power feed to the light's I mite do this any way wouldn't hurt Being you are looking for the fault Check the wire nut's maybe tighten them or check for looseness ?

Re: Electrical Quirk question

#6

Re: Electrical Quirk question

GalenV in Iowa

>I have flipped a light toggle switch in a hurry and since I did not get it all the way up it snapped back down to off. Have done the same thing with decora switches and pushed the rocker up but on bringing my hand down still brushed the switch back off.

Like others noted it may have been a poor switch internals not tripping or wires not tightend.

In my case it is usually operator error.

Re: Electrical Quirk question

#7

tracing electrical problems

Bill Houghton, Sebastopol, CA

>Three possible likely causes:

1. Bad switch.

2. Loose connections.

3. Break in wire somewhere in the wall that's making/breaking intermittently.

The last is the least likely (aren't you lucky). The first two are probably about equally likely. I'd check connections first. If the circuit in question is one that family members depend on a lot, I'd have a switch at hand; otherwise, get one only if you need to (NOTE: take the circuit breaker switch with masking tape or something to indicate not to turn it on while you're away).

Since you replaced the switch, check that box first - I'm not criticizing you when I say that the last place in which work occurred is the first place to look for problems, merely reporting on my own experience.

Re: Electrical Quirk question

#8

Hmm, how'd he know that?

Tony Shaftel

>...the last place in which work occurred is the first place to look for problems...

And I thought that was only true for software developers. :-)

Re: Electrical Quirk question

#9

While we're talking switches...

Tony - Memphis

>I found one in my shop that was warm to touch when I turned it off on the way out. Turns out the electrician must have had this switch rolling around in his truck for years. It had seen lots of moisture and was corroded. Glad I caught it before it was a real issue.

Now I have a question. Now and then, I notice a switch will make a popping noise when the switch is turned to the on position. Sounds like an electrical "pop." I've noticed this on more than one switch. No issues, just that popping sound. Can't verify it is electrical vs mechanical, but I've always wondered.

Tony

Re: Electrical Quirk question

#10

Re: While we're talking switches...

del schisler

>sound's like it is time to replace the tip's are getting pitted bad