Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

OT - Gas furnace advice

Posts

OT - Gas furnace advice

#1

OT - Gas furnace advice

Joe Grittani

>Greetings from the increasingly colder Great Lakes region -

My forced air gas furnace is working okay, but I know I'm pushing my luck. The installation tag is still in place - April, 1959 - yep, that's five nine. The central a/c unit probably went in in the late 60s and definitely needs replacing. I did some research a few years ago and discovered that American Standard was the highest rated manufacturer for quality/durability, but I don't know if that's still the case. I also don't know about the value of 90 - 95% efficiency ratings or two stage blowers.

With tax breaks and a utility rebate program this looks like the time.

I'm looking for quality and efficiency of operation and maintenance at a reasonable price, whatever that might be. Somwhere between a Yugo and a Lexus. I have about 1,400 sq ft on two floors + basement.

Thanks in advance for any advice, rants, warnings or magic incantations.

Joe Grittani

Re: OT - Gas furnace advice

#2

Re: OT - Gas furnace advice

Fred Davis

>By all means replace it, it could save your life , if it doesn't have a cracked fire chamber , then your very lucky.

FredD

Re: OT - Gas furnace advice

#3

Re: OT - Gas furnace advice

John Veerkamp, Western Mo

>I had American Standards installed last spring. I deficitely like the variable speed blower. It ramps up as needed. if less cooling/heated load is required it goes 50% or 85% speed. Keeps it quiter.It only goes to 100% under higher demands. 90% of all demand is at lesser levels. Our new system is enough more efficient that our electricity usage is down noticeably. Be sure to get the digital-programable thermostat. It sure makes keeping the house comfortable easier and cheaper.

John

Re: OT - Gas furnace advice

#4

Re: OT - Gas furnace advice - -DIY !

Pete in Holland, MI

>Furnaces are pretty much commadity items anymore. Valves, controllers, fans, sensors are from only a few suppliers anymore. Differences are now in the sheet metal, for the most part.

I have retrofitted new gas furnaces into my home, and that of about 7 other people in the last 10 years. Unless you are looking for an entire system overhaul, new furnaces are much smaller than the older ones and make it easy to adapt to the old duct work.

If you can take careful measurments to provide to the duct builder, savy with electrical & black iron plumbing, they are pretty easy to install. Larger furnace insallation houses do their own sheet metal work and can guide you thru the adaption process.

Do a nice job installing it, then call your furnace guy in to inspect it an adjust the pressure regulator. Cost is around $50 or so for that service. Furnaces are pretty much pre-set from the factory and should run after you install it properly, then call the furnace guy later, if you desire.

Put a 75,000 btu, 95% efficency, 2 speed LP gas furnace in my dad's place a couple years ago for a total of $850. Furnace suppliers are reluctant, but will sell you furnaces out the door.

Be advise though: Most states have laws that, if an furnace guy inspects your furnace and sees a hole in your heat exchanger, he is obliged by law to lock down your furnace, then the over-the-barrel clause will kick in and you'll be be installing an expensive furnace that day.

First furnace took about 4 hours to replace. Takes a couple hours now.

Pete

Re: OT - Gas furnace advice

#5

Re: OT - Gas furnace advice

Joe Grittani

>I failed to mention that I had it inspected and tuned up last winter and everything was sound. Also, it's natural gas, not propane.

Joe

Re: OT - Gas furnace advice

#6

Re: OT - Gas furnace advice - -DIY !

Fred Davis

>Making a furnace installation sound no more difficult then changing the filter Cartridge in your whole water filter is (and many can't) dangerously misleading.

Not only is it illegal wherever the National Plumbing code and UBC have Jurisdiction, it gives your home owners insurance a wide loop hole to avoid paying for fire damage.

If somebody dies or is seriously injured, because you lent a neighborly helping hand and did the installation, you will need a really good defense lawyer.

The exposure to possible litigation is why supply houses won't sell to non -craft people and generally only to contractors.

FredD