Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Loft ladder advice needed.

Posts

Loft ladder advice needed.

#1

Loft ladder advice needed.

Ray Carson - Lawrenceville, NJ

>It's been a while since I've posted. How's everybody doin? I've been busy doing my Dad thing, keepin my nose clean at work. We had a recent layoff due to the recession and I'm still working on my entertaiment cabinet.

I was asked by one of my wife's co-workers if I wanted to build a ladder. The ladder is to access a newly formed storage loft area made by a recent house addition. The "client" is quite anal about the details. I don't mind as I can be the same way. What I looking for is some advice on ladder building. Should be a no brainer except there are particulars that I will need to adhere to.

The ladder is being hung on the wall in the hallway of a colonial style home. It's meant to be decorative and funtional. The reason is it's being used on the second floor and the loft is accessed a couple of times a week for thier three boys "stuff". Therefore storing a ladder in the garage or bedroom is not wanted. The ladder will be approx. 9'-7" long.....and......they want a tapered look instead of two parallel stringers. Here are the specifics:

Length: 9'-7"

Wood: Oak or Maple stained with satin finish. (They wanted pine but I'm trying to discourage them away from a softer wood towards something more durable)

Treads: Round or Flat? (Again, I'm trying to steer them in the right direction. Round might be easier to hang but I feel flat treads are a bit more stable.)

Stringers: Tapered not parallel. I was thinking 1" x 3" with 3/4" treads. Possibly a threaded rod underneath to keep things from pulling apart.

One sided ladder, not an A-frame.

I know it's JUST a ladder but they are looking for something a bit more decorative as I stated as it will exposed as a piece of furniture. I was thinking about incorporating some dovetails in to joinery as well. Could I do this with the treads or maybe just the top step without effecting the strength drastically. I could always beef up the tread thickness. ???

Any advise is appreciated.

Thanks WoodCentralians,

Ray

Re: Loft ladder advice needed.

#2

Re: Loft ladder advice needed.

Bill Houghton, Sebastopol, CA

>Be sure to use wood with no grain runout on both the stringers and treads.

I'd go with flat treads. Regardless of how period round may be, they're uncomfortable in use.

Re: Loft ladder advice needed.

#3

Re: Grain runout ???

Ray Carson - Lawrenceville, NJ

>

Re: Loft ladder advice needed.

#4

Re: Grain runout - I "googled" it Bill.

Ray Carson - Lawrenceville, NJ

>I understand what you mean. Good advice. Thanks.

Ray

Re: Loft ladder advice needed.

#5

Re: Loft ladder advice needed.

Glenn Madsen, near San Francisco------WebKitFormBo

>I would choose something other than maple if stain or dye is needed for the aesthetics. Maple doesn't take color into the grain. A gel stain might have durability issues on a ladder.

In California, we have Tannoak, which does what you want. In white oak area, that might be a good choice.

Bill's grain runout comment makes sense.

Re: Loft ladder advice needed.

#6

Re: Loft ladder advice needed.

Ed Mulligan, Caoe Cpd MA

>Myself, I probably wouldn�t accept this work due to potential liability.

I have a pull-down attic stairway made of pine, circa 1968. The treads, 3 � inches wide, are dadoed in the sides and secured with nails. The factory also put threaded rods at the ends of the folding sections. Over time, the nails lost their grip and the treads were in danger of falling out of the dados. I added a threaded rod under each tread. Shortly afterward the local building inspector (6� 6� and at least 300 pounds) had to use the stairway. It groaned a bit but stayed together!

The issue with oak or maple will be weight. How much will it weigh and is it light enough for the average homeowner to manipulate? Whatever wood you use, it has to be free of knots, runout, and anything else that might weaken it.

Flat treads only work at one angle while round ones work at any angle. I think for this application the flat treads would be most comfortable. Speaking of angle, steeper angles will use less floor space in use. More shallow angle will be easier to climb, especially with items in hand, but will require stronger stringers.

Look into some way to secure the ladder at the loft end so it can�t kick out in use.

Re: Loft ladder advice needed.

#7

Re: Loft ladder advice needed.

GalenV in Iowa

>Ray

Is the 9'-7" the vertical height from floor to floor of loft? Even if the ladder is at 80 degree to floor like a rolling library ladder it will be hard to bring "stuff" down, if larger than a book. Do they need to step thru the ladder to actually stand on loft. If so the rails need to extend up so they have something to grab hold of to step thru.

The old library ladder I copied one from was of white oak, had 1 1/8 x 3 1/4 side rails and 4 1/4" x 3/4" thick treads. Each has maybe a 1/4" or 5/16" stay rod. It was 16" wide with no flair to bottom.

I have seen one that the lower section was hinged to flip up against the wall and then pivot at the top to allow it to swing down as the bottom was pulled out to set the ladder angle.

Ladder would be on the heavy side if it is just stored flat on the wall and moved to get to the loft.

Galen

Re: Loft ladder advice needed.

#8

Paul Kramer

Re: Loft ladder advice needed.

Paul Kramer

>Ray,

I built a set of fold-down stairs for my shop about 24" wide with a total rise of about nine feet. I used nominal southern yellow pine 2 X 10's for the stringers, the same for the treads planed down to 1" thick, and reinforcing 1 1/8 diameter oak dowels under each tread. I oriented the grain of the dowels vertically (when under load) and tapered the holes in the stringers so as to allow for wedging of each dowel-end to make sure that the stringers don't separate. The wedge cut in the dowel ends were oriented to assure that the wedges worked against the long grain of the stringers (The axis of the wedges were perpendicular to the long axis of the stringers.). As it turned out I had to turn down the dowels to 1" on the ends. The treads are housed in shallow dados at each end.

The stairs ended up being very heavy and I needed mechanical assistance to raise and lower them. Initially that was a block and tackle then ended up with a salvaged winch from an old fashioned chair lift. That winch with it's limit switches ended up being perfect. The picture doesn't show the hinged part at the bottom but you can clearly see the stringers, treads and dowels. I specifically fabricated it so that when still folded the stairs would swing nearly completely out of the way of the hatchway opening so the largest items could be lifted.

Liability is a big issue. Ever wonder why you can't buy the hardware to make a library ladder?

Paul


img

Re: Loft ladder advice needed.

#9

Re: Loft ladder advice needed.

Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6

>JL, I have done a few ladders of this nature through the years.

What I have found that makes a good easy repeatable joint, is a tapered sliding dovetail joint.

The front of the tread may be 1/8" thicker than the back. Easy to do, just make a sub- bed that fits under the planer bed, or just tilt the TS and re-saw it. Then make a router template to match the front to back angle.

Running the tread on a table router standing on end with each side against the fence, will give you a wedge shaped dovetail tenon.

Setting the template to the right pitch for the rise run ratio is not that hard to figure out, so the tread slides in from the front until it snugs up just right.

I would stay away from the un-parallel part. You can add other details to give a custom look which are easier to accomplish without adding that complexity. Think of an arc or G&G cloud-lift shape sawn into the plan view of the treads.

That sliding tail really locks everything together when it gets glued together. You won't ever need to worry about anything working loose or breaking.

Re: Loft ladder advice needed.

#10

Re: Loft ladder advice needed.

Bill Houghton, Sebastopol, CA

>"...steeper angles will use less floor space in use."

Remember, though, that there's a maximal vertical angle. The rule of thumb I was taught, which works great, is to stand at the foot of the ladder and put your arm out straight. If you can grasp a rung without bending your arm, the angle is right; otherwise, it's too steep. Exactly what this angle is in degrees I know not.

Also, the shallower the angle - the farther out the foot is - the more the strain on the ladder, requiring beefier parts.

Re: Loft ladder advice needed.

#11

Re: Loft ladder advice needed.

Ray Carson - Lawrenceville, NJ

>Hello Galen,

Is the 9'-7" the vertical height from floor to floor of loft?

No. The rise is 9'-0 1/2" and the run requested is about 36" away from the wall. This calculates into a +/-73 degree angle.

Do they need to step thru the ladder to actually stand on loft. If so the rails need to extend up so they have something to grab hold of to step thru.

No. Once at the top you crawl onto the floor and into the space. You can only stand up in the center of the space near the ridge.

The old library ladder I copied had 1 1/8 x 3 1/4 side rails and 4 1/4" x 3/4" thick treads. Each has maybe a 1/4" or 5/16" stay rod. It was 16" wide with no flair to bottom.

Ladder would be on the heavy side if it is just stored flat on the wall and moved to get to the loft.

The dimensions for the stringers and treads are almost exactly what I had in mind. I'm concerned with weight also.

I will weigh your input heavily Galen. Good advice here.

Thanks,

Ray

Re: Loft ladder advice needed.

#12

Re: Loft ladder advice needed.

Ray Carson - Lawrenceville, NJ

>Hello Ed,

I've read all the responses here and your one of two who recommended turning down the project. If I decide to go ahead with this, I guess I'll need to make it clear that I'm not a professional ladder designer, etc., etc., etc. Liability is not something to mess around with. Even if it is a "friend".

I have an a garage pull down stair like yours that is, let's say, on the verge of blowout. I need to replace very soon. I here what your saying.

How much will it weigh and is it light enough for the average homeowner to manipulate? Whatever wood you use, it has to be free of knots, runout, and anything else that might weaken it.

As I wrote to Galen, I'm concerned with weight too. The home owner says he is the only one that will use the ladder, maybe his wife once in a while. He weighs 195 lbs. The wife is probably in that ballpark.

Flat treads only work at one angle while round ones work at any angle. I think for this application the flat treads would be most comfortable. Speaking of angle, steeper angles will use less floor space in use. More shallow angle will be easier to climb, especially with items in hand, but will require stronger stringers.

I don't have much room for play here. The space is what it is. I agree on the strength regardless of angle of pitch. I don't want a failure. I like the flat tread design myself. Round steps dig into the arch of your feet and can be tricky to place a foot on if your not careful or blind from holding a load in your arms and not being able to look at your feet.

Look into some way to secure the ladder at the loft end so it can�t kick out in use.

Not a bad idea if I can work that into the design.

Thanks for all the advice Ed.

Ray

Re: Loft ladder advice needed.

#13

Re: Loft ladder advice needed.

Ray Carson - Lawrenceville, NJ

>Hello Keith,

I would stay away from the un-parallel part. You can add other details to give a custom look which are easier to accomplish without adding that complexity. Think of an arc or G&G cloud-lift shape sawn into the plan view of the treads.

Yeah the tapered thing I'm not crazy about but that's what the client wants. About 12" wide at the top and 18" to 20" at the bottom. They also want to incorporate some brass into the mix. I like the tread design ideas.

Thanks,

Ray

Re: Loft ladder advice needed.

#14

Re: Ladder -Thanks everyone. Good advice here.

Ray Carson - Lawrenceville, NJ

>

Re: Loft ladder advice needed.

#15

library ladder hardware

Dave Bair, Eaton Rapids, MI

>A Google search for "library ladder hardware" turned up a large number of sources for the hardware, including Rockler.

Re: Loft ladder advice needed.

#16

Paul Kramer

I guess things have changed since I last looked

Paul Kramer

>