Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Shop Heater Connection

Posts

Shop Heater Connection

#1

Shop Heater Connection

howard

>I bought a Hot Dawg ceiling mounted heater and was thinking of running the gas line outside. 3/4" balck iron pipe about 40' to the unit. This would be the shortest distance, otherwise I will need to run inside the house. Is this allowed, are there reasons why this would not be the right thing to do, other reasons, etc. Thanks for your help.

Re: Shop Heater Connection

#2

Re: Shop Heater Connection

Bill Houghton, Sebastopol, CA

>Black pipe, when not protected from the weather, has to be wrapped in a specific protective cover. You can get the pipe already wrapped (sleeved, actually), and then use the matching tape to cover joints.

I don't live in frost country, so I'm not familiar with any requirements for burying or anything.

You might consider talking to your building inspector; this is one of those items that, if you don't do it right, could make problems. Fireballs in the back yard tend to lower property values, and your homeowner's insurance might not cover anything that's not done under permit.

Re: Shop Heater Connection

#3

Gas scares . . .

steve mackay

>heck out of me. If in doubt (read : always) I, at least, drop by city hall and ask. Mine even has a customer desk for Joe Citizen to check codes and regs. I'm paying their salary so might as well take up some of their time. If I'm only asking questions I never tell them who I am or where I'm working. If you do, they start wanting permits you may not wind up needing.

Re: Shop Heater Connection

#4

Re: Shop Heater Connection

Bruce, a MN Galoot

>I work for a public utility, and our gas dept. fields questions like this all the time. Give your utility a call. They'd much rather tell you up front than tell you the bad news after the fact.

Bruce

Re: Shop Heater Connection

#5

Re: Shop Heater Connection

Pat Riley

>Depending on where you live, black cast iron pipe needs to be sheathed or encased in a pvc 'conduit' if it is to be outside or underground.

I agree with the others, call the building dept.

Re: Shop Heater Connection

#6

Re: Shop Heater Connection

Don at Central Illinois

>I ran special plastic pipe made for gas. Had to have a plumber (read licensed) order it and I picked it up and paid for it. I wasn't allowed to buy it myself. Ran black pipe to the basement wall, connected it to the plastic and then ran black pipe for the plastic in the garage to the heater. I do live in 'frost' country and buried it about 48" deep along with the electrical, water and phone.

Re: Shop Heater Connection

#7

Re: Shop Heater Connection

gary peterson

>I live in north jersey. I installed hot dawg last year, needed to run 70ft in house and underground. After thoughtful reflection I had a plumber do all the work. According to town's code, needed to be 18in deep, didn't matter if was black pipe or the new flexible stuff.

My estimates were, rounded now, $1800 for pipe and $1400 for flex. I went with the pipe. Didn't need a wrap, altho that can be added, pipe was smeared with axle grease(I guess). estimate included from the gas meter through my basement, out the basement wall, into the garage right to the heater connection. I did the digging. Plumber did neat and clean work.

Plumber suggested, and I thought great idea, that with the distance involved and I have a house gas furnace we should use one inch pipe in order to keep up with demand.. The other guy said 1/2 inch would be ok. Love the heater, 60btu model, three car garage.

Re: Shop Heater Connection

#8

Re: Shop Heater Connection

gary peterson

>OH YEAH, strongly suggest DO NOT put pipe or flex into pvc, all you need is a small leak and the pvc with capture providing a reservoir of potential explosive gas.