Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Groove vs dado...what's the difference

Posts

Groove vs dado...what's the difference

#1

Groove vs dado...what's the difference

Terry Alexander

>Ok....maybe a stupid question. But I like to be precise in my woodworking and in my vernacular.

Like the subject line says: "What's the difference in a groove and a dado?" Looks like the same thing to me.

As always....TIA

Terry Alexandfe in West Texas

Re: Groove vs dado...what's the difference

#2

Re: with grain vs cross grain..

Mike Hamilton

>

Re: Groove vs dado...what's the difference

#3

To add a bit

Bill Houghton, Sebastopol, CA

>Groove: with the grain

Dado: across the grain

Back in the hand tool days, this required different tools to accomplish, which is probably why the differing terms were necessary.

Re: Groove vs dado...what's the difference

#4

Whaddya mean

Neal in San Jose

>"Back in the hand tool days"? That is today! If you are tired of sanding, use a bench plane; if you want a tennon to fit exactly, use a rabbet plane; if you are tired of your corners being slightly off, use a shooting board. In other words, if you are tired of the inaccuracies, wasted time, noise, dust and fiddling required by power tools - Come on over to the dark side!!! You can continue to wear your "Normite" red flannel shirt, tho it may be a little hot with the calories you will burn.

Re: Groove vs dado...what's the difference

#5

Just so you know, Neal,

Bruce, a MN Galoot

>Bill is the moderator of the "dark side" here at WC.

Re: Groove vs dado...what's the difference

#6

Re: To add a bit

Grant Wilkinson

>... and then, there's rabbets.

Re: Groove vs dado...what's the difference

#7

Oh, I agree

Bill Houghton, Sebastopol, CA

>I meant back when hand tools were the dominant technology.

Power tools don't, for the most part, seem to notice which way the grain runs, but hand tools do, so I imagine it was necessary to have a different term for each direction in recognition of the differences in production.

Re: Groove vs dado...what's the difference

#8

So

Bill Houghton, Sebastopol, CA

>what do you call it when it's cut at a skew across the grain, say at 45 degrees?

A grado?

A doove?

Re: Groove vs dado...what's the difference

#9

Re: So

Don Orr

>How about Groovy, man. ;-))

Re: Groove vs dado...what's the difference

#10

Re: To add a bit

Howard Acheson

>>>> Groove: with the grain

>>> Dado: across the grain

In the "olden days" a "groove" was known as a "plow" (plough in the UK). Hence a plow plane was used to cut a groove with the grain.

In fact, an old book I have talks about grooves as being any non-through cut in wood whether with or across the grain. A dado is an across the grain groove and a plow is a groove parallel with the grain.

Re: Groove vs dado...what's the difference

#11

I knew that

Neal in San Jose

>I didn't remember it, but I knew it. CRS kickin' in.

Re: Groove vs dado...what's the difference

#12

if I had to admit to every instance of CRS

Bruce, a MN Galoot

>I'd never get anything else done.

bh

Re: Groove vs dado...what's the difference

#13

'Sokay

Bill Houghton, Sebastopol, CA

>you raised a good point.

Re: Groove vs dado...what's the difference

#14

What about plywood? :-)

Terry Alexander

>

Re: Groove vs dado...what's the difference

#15

Re: To add a bit

Bart Leetch

>... and then, there's rabbets.

Wabbit's did I hear someone say Wabbit's

What's up Doc ???

Re: Groove vs dado...what's the difference

#16

Re: Psychedelic!

Ned Bulken

>