Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Boice-crane planer

Posts

Boice-crane planer

#1

Boice-crane planer

g

>I have a Boice-crane planer and I would like to talk to someone about proper set-up. The planer seems to be working fine, and then the stock will stop feeding through the machine. Do I set more or less tension on the rollers? Is that the problem? My direct email is: p38@fcs.net

Thank you,

g

Re: Boice-crane planer

#2

Re: Boice-crane planer

Ken Oakley-Sunny St. Cloud,Fla

>Could be the rollers are just glazed over. I clean mine on my Delta benchtop planer with a rag wet with lacquer thinner.

Re: Boice-crane planer

#3

Rick L

Re: Wax the bed...

Rick L

>Wax the bed more often. I have serviced machines commercially and half my service calls for feed issues only required waxing the bed. You should see the looks on their faces when I did that. Of course I checked all the settings to make sure. Keep the bed rolls about .003"

BTW...I used to own that machine and it's the heaviest duty 12" planer made.

Re: Boice-crane planer

#4

Re: Wax the bed...

Fred Davis

>Waxing planer beds wil eventually contaminate your wood if it is not throughly sanded.

A better product ,which will not stick to the wood is any brand of Baby powder , Corn Starch, or Talc.

Regular use will fill the cast iron tables and make them slicker then a Mole's ass.

Great for tablesaws too.

Boice -Crane made great machines, I still use a Oscillating drum sander by them.

If the pressure bar on the planer is adjustable and the better ones are , you might try backing it off a fraction.

FredD

Re: Boice-crane planer

#5

Re: Boice-crane planer

Bill Tindall, E.TN

>If the machine has a pressure bar behind the cutter head (it will be on top just past cutter head) it may be too low. For machines with a pressure bar, feeding problems are most often a result of this part being adjusted too low.

Re: Boice-crane planer

#6

Re: Boice-crane planer

Roy Girolami------WebKitFormBoundary9yANUT8mn8C+Zo

>I have one of those planers and had a problem when I was using it to plane some lyptus. The wood was so hard or abrasive that it dulled the knives so much that the wood wasn't being cut, so it just stopped feeding. If you go to the old woodworking machine site, you can download an owners manual.

Roy Girolami

Apex,NC

Re: Boice-crane planer

#7

Rick L

Re: Disagree... *LINK*

Rick L

>Waxing the bed won't hurt anything. Typically you sand the wood anyway. Commercial moulders have wax injectors to keep the beds slick.

Baby powder is too slow in a commercial shop. Typically we wax the beds and any metal part that goes against wood regularly. Could be every hour in some applcations.

35 years in commercial factories and custom shops as machine repair and problem solving


Slip it lube

Re: Boice-crane planer

#8

Rick L

Re: Pressure bar...

Rick L

>Good point. Many of the older machines have a fixed pressure bar (the bar just past the cutter head which keeps the wood from lifting into the head at the end of the pass) so as the knives dull they get caught under the pressure bar, so I typcally set the pressure bar a few thousandths above the cutter circle to allow for dull knives. Many of the newer machines have a spring loaded pressure bar so it's more flexible in the setting of the bar.

Still you can't wax the bed often enough!