Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Dealing with difficult veneers

Posts

Dealing with difficult veneers

#1

Dealing with difficult veneers

Thomas S Stockton------WebKitFormBoundaryRU4sWQOIA

>Last year I had a bed project that called for walnut burl veneers, I had a few problems with bubbles in the burl panels. I was able to fix the problems but I wanted to find a better way to deal with difficult veneers like burls. This led me to Vacuum Pressing Systems excellent online forum. They recommend a process called 2 ply where you veneer a backer veneer to the burl to stabilize it. For my current desk project I used this process and it worked really well.

I flatten veneers using a commercial flatting agent, and then use my vacuum press to flatten and dry them. You can easily make your own flattening agent but I find it is easier to buy and have ups deliver it.

moisten both sides of veneer with solution

hang dry for 10 minutes or so

place between paper and cauls and press in veneer press. I use a layer of unprinted newsprint against the veneers and then add a couple of layers of newspaper between the unprinted paper

I change the paper three times the first day and leave under pressure overnight.

On the second day remove from the press and put in fresh paper. I don�t put it back in the press, instead I weight the stack on a flat surface. I change the paper three times and the next day it is good to use

Pic is of burls hang drying


img

Re: Dealing with difficult veneers

#2

Dealing with difficult veneers part 2

Thomas S Stockton------WebKitFormBoundaryRU4sWQOIA

>2 ply technique

I used walnut for the backer because some of the edges were going to show and I didn�t want a different colored veneer showing. Poplar, maple and mahogany also work well, it doesn�t need to be the same material as the face. If you are 2 plying something other than a burl (which doesn�t really have a grain direction) the backer grain runs at 90 degrees to the grain direction of the face

I used modified urea formaldehyde glue (Unibond) for this project because it is a very rigid glue line and has a low moisture content

The next step is to cut the veneer to rough size, the burl is cut a couple of inches over in both directions. The backer is cut to the same width as the burl but four inches longer . At this point I also lay out my veneer like it will be on the panels and place a piece of blue tape on the face so that it gets glued up in the correct sequence.


img

Re: Dealing with difficult veneers

#3

Dealing with difficult veneers part 3

Thomas S Stockton------WebKitFormBoundaryRU4sWQOIA

>I then make cauls to press the veneer. The top caul is the same size as the burl, the bottom caul is a little longer than the backer.

I then tape the backer down to the caul so that when the glue is applied it doesn�t curl up and make my life miserable


img

Re: Dealing with difficult veneers

#4

Dealing with difficult veneers part 4

Thomas S Stockton------WebKitFormBoundaryRU4sWQOIA

>I then apply glue and put it in the vacuum press


img

Re: Dealing with difficult veneers

#5

Re: Dealing with difficult veneers

Thomas S Stockton

>Benefits

The 2 ply makes burls which tend to be brittle and finicky to work with much stronger and stable. The other thing I noticed is that they press a lot flatter and it takes much less sanding to get a good surface, which is really important when dealing with veneers.

After 2 ply is made.

joint like you would normally

If using burls and applying to a curved surface make sure grain goes in the correct direction so it bends easier


img

Re: Dealing with difficult veneers

#6

Dealing with difficult veneers part 5

Thomas S Stockton

>Benefits

The 2 ply makes burls which tend to be brittle and finicky to work with much stronger and stable. The other thing I noticed is that they press a lot flatter and it takes much less sanding to get a good surface, which is really important when dealing with veneers.

After 2 ply is made.

joint like you would normally

If using burls and applying to a curved surface make sure grain goes in the correct direction so it bends easier


img

Re: Dealing with difficult veneers

#7

as an added bonus you get #5 twice

Thomas S Stockton

>

Re: Dealing with difficult veneers

#8

Re: as an added bonus you get #5 twice

Sgian Dubh

>Good write up of a very useful technique for working with those tricky veneers. Slainte.

Re: Dealing with difficult veneers

#9

Ellis Walentine

Excellent post, Tom

Ellis Walentine

>Outstanding veneer, too. Question for you: How do you decide when this technique is necessary? Where I'm going with this is that a lot of non-flat veneers flatten well enough that you can lay them down without bubble worries. Is there a particular tip-off that a particular veneer is a candidate for backing?

Thanks so much for a great write-up.

Ellis

Re: Dealing with difficult veneers

#10

I have an easier solution Tom.....

Thomas Skaggs, Foothills of Mount Level

>....Just send that that difficult burl veneer to me and I will gladly exchange and send you some nice flat clear figure veneer. How easy is that? ;-)

Seriously, this was a very good post! I learned something good!!!

Tom

Re: Dealing with difficult veneers

#11

Re: Excellent post, Tom

Thomas S Stockton

>This was the first time I used the 2 ply technique. I do a fair amount of veneering and the only time I've had real problems was with burls. For me the added benefits of making the burl much easier to handle and how flat they become by using 2 ply is well worth the effort. The only material I've ever flattened or softened is burls because a little bit of ripple or puckering in veneers really doesn't cause any problems at all.

I came across this info from Vacuum Pressing Systems forum and tweaked it for my own use, they are big proponents of it and recommend it for stabilizing crotches and anytime you might be worried about pressing problems. For me it takes some extra time and the only time I would probably use it would be on burls and crotches.

I would check out the Vacupressing Systems forum it has a lot of great info and is the best source for veneer questions out there.

Tom

Re: Dealing with difficult veneers

#12

Alan Young

Thanks for a great write-up!

Alan Young

>