Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Picture Tiles On A Table------WebKitFormBoundarytI

Posts

Picture Tiles On A Table------WebKitFormBoundarytI

#1

Picture Tiles On A Table------WebKitFormBoundarytI

Russ Ellsworth------WebKitFormBoundarytI3PsYIW0Sq1

>I want to use some 4"x4" ceramic picture tiles in a 12"x12" pattern on the top of a "foot of the bed" chest. The chest will be painted with milk paint. The top will be white oak stained. My questions are, 1. What is the best way to glue the tiles down...., regular tile set or? 2. I think I have to grout the tile but with what? Regular grout or??

Would you recommend insetting the tile into the top. Laying the tile on the wood surface and using some type of edging around them. Or any other suggestion. I'm comfortable with building the chest itself but the tile picture has me a bit concerned. Thanks for any ideas or direction you all can give.

Russ E.

------WebKitFormBoundarytI3PsYIW0Sq1+tCx

Re: Picture Tiles On A Table------WebKitFormBoundarytI

#2

Re: Picture Tiles On A Table------WebKitFormBounda

Fred Davis

>Russ,

since the the tile is on a chest lid I assume it will be raised and closed occasionally .

So I would set the tile in a adhesive caulk like PolySeamSeal which will never let go and also use it for the grout.

There are some sanded grouts available in caulking tubes, whether they would be flexible enough I couldn't say.

As for the edges, they are exposed to chipping if struck, so I would personally use a wood surround, or at least have the border tiles bull

nosed.

FredD

Re: Picture Tiles On A Table------WebKitFormBoundarytI

#3

Re: Picture Tiles On A Table------WebKitFormBounda

Lee Schierer - McKean, PA

>I made a tray with picture tiles. I mounted them with a flexible mastic and grouted tehm with white silicone so tehy could be cleaned. I say the tray a few months ago and the tiles and grount look fine after about 10 years.

Lee


img

Re: Picture Tiles On A Table------WebKitFormBoundarytI

#4

Re: Picture Tiles On A Table------WebKitFormBounda

George@Colonel's Workshop-Havertown PA

>Good Afternoon Russ,

I had to do offee and end tables for a client several years ago. They wanted the tops to be tiled. I used 3/4" ply for the top, biscuiting 2" wide mitered hardwood around the perimeter. The biscuits permitted me to offset the level of the ply to the thickness of the surrounding hardwood. When the tile was applied and grouted, it was all tyhe same level, and looked great. Care when grouting, however. Better to mask off adjacent surfaces. Care also with the design--will anybody sit on the tiled surface causing it to flex?

George

Re: Picture Tiles On A Table------WebKitFormBoundarytI

#5

Re: Picture Tiles On A Table

Russ Ellsworth

>Thanks for the tips. It is possible that the lid could be sat on so I will have to make sure the lid is rigid enough. Grouting and sticking with white silicone sealer sounds pretty good too. I have been thinking about using plywood for the lid but I think the white Oak will look better when stained. I guess I could try veneering over ply but that would be another new skill for me. One at a time may be enough!!!

Re: Picture Tiles On A Table------WebKitFormBoundarytI

#6

Re: Picture Tiles On A Table

Fred Davis

>One more tip about the grouting, using caulk, if you use Silicone , while it is great at sticking , it is no better then PolySeamSeal and does not clean up easily with water which PolySeamSeal does and is a great advantage when your grouting with adhesive caulk.

FredD

Re: Picture Tiles On A Table------WebKitFormBoundarytI

#7

Re: Picture Tiles On A Table

Russ Ellsworth

>Thanks again for all the tips. I will try to post w/pics when this little project is done.

RussE

Re: Picture Tiles On A Table------WebKitFormBoundarytI

#8

Caulk It Up to Experience, Russ

George@Colonel's Workshop-Havertown PA

>

Re: Picture Tiles On A Table------WebKitFormBoundarytI

#9

Ellis Walentine

I second plywood

Ellis Walentine

>If it were me, Russ, I would make a white oak frame with a plywood panel glued in, similar to what George did. Leave enough depth between the frame and the plywood for your tiles plus about 1/16" for a layer of floor mastic spread with a notched trowel. Break the edges of the white oak so they are slightly rounded down into the grout space so you don't get any sharp wood edges after you smooth out the grout. I would not use white silicone as the grout because it looks so unnatural, but you might get away with one of the sand-colored "grout" that comes in tubes, usually gray or tan. These have enough texture to look natural, and they are definitely more flexible than typical tile grout, although there are some excellent pre-mixed tile grouts out there that might be easier to handle.

Sounds like a fun project. Keep us posted on your progress.

Ellis Walentine, Host