Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Allen Wrench question OT

Posts

Allen Wrench question OT

#1

Allen Wrench question OT

Gary Smyth

>Does anyone know if a 3/8 Allen wrench can be threaded with a 3/8 die? I'm asking because I'm thinking the steel on an Allen wrench might be too hard for the die? Failing that, does anyone know where I can find about 8" of 3/8" hex steel rod that is not hardened? I need to feed one end into a threaded female coupling and use the unthreaded end to connect with a drill.

Re: Allen Wrench question OT

#2

Re: Allen Wrench question OT

Lee Schierer - McKean, PA

>The allen wrench is going to be too hard to cut threads in. It could be annealed, but that might not be easy to do.

In this case McMaster-Carr is you friend as they sell hex bar stoick in several material choices that could be threaded.

Lee

Re: Allen Wrench question OT

#3

Re: Allen Wrench question OT *LINK*

Bill Turpin in WNC mountains

>Be sure that you get your measurement correct as to corner to corner or flat to flat


McMaster

Re: Allen Wrench question OT

#4

Re: Allen Wrench question OT

Wess in NJ

>Yes, allen keys are hardened, so your not going to thread without first annealing. Actually 3/8 hex is measured across the flats, so you can't thread without turning an end down. If I understand what you are trying to do, it seems a piece of 3/8 all thread with a hex coupler threaded on and then welded or cross pinned would work.

Re: Allen Wrench question OT

#5

hex on me

Gary Smyth

>A hex coupler is something that might work but (hummmm) again where would I find a hex coupler that fits a 3/8" threaded rod but retains the same 3/8" diameter on the hex end? A coupler will get me to about a 1/2" to 5/8" diameter and in this instance that's too large. I need a 3/8" max from the thread and the hex.

Re: Allen Wrench question OT

#6

Jason Roehl in Lafayette, IN

Re: hex on me

Jason Roehl in Lafayette, IN

>If you're just looking to get 3/8" threaded something-or-other into a drill, just hand-file some flats onto the 3/8" all-thread and chuck it directly into the drill. You can even chuck it (tightly) before filing to mash down some threads and give you a file guide.

Jason

Re: Allen Wrench question OT

#7

Lee and Bill

Gary Smyth

>Thanks for that. The Mc-C stuff may well work as the steel is not hardened and that formula has some lead mixed in to make it easier to machine. I'm going to call in the AM and ask about their alternatives and if a 3/8" threaded section is possible with a typical hand worked die..

Re: Allen Wrench question OT

#8

Re: hex on me

Wess in NJ

>I'm assuming that your plan is to chuck the hex end in a 1/2 capacity drill?

Re: Allen Wrench question OT

#9

Re: Lee and Bill

Lee Schierer - McKean, PA

>As others have stated 3/8 hex stock is 3/8 across the flats, the corners are larger and will have to be removed for your 3/8 die to work. Most small machine shops can do this for you in a few minutes and many of them are very hungry right now for work.

Lee

Re: Allen Wrench question OT

#10

Re: Allen Wrench question OT

Ron Jones

>Name brand hex wrenches will not work. I'll bet the cheapos will. I've seen pretty soft and weak off brand hex wrenches.

Re: Allen Wrench question OT

#11

seems to me

John b

>that you could buy a 3/8" bolt and cut off the head. Lots of drill bits don't have hexes on them and work just fine.

John b

Re: Allen Wrench question OT

#12

In that size,

Bill Houghton, Sebastopol, CA

>most files can remove the corners too, for a lot less than a machine shop.

Re: Allen Wrench question OT

#13

Thanks to all. Now I have it

Gary Smyth

>The perfect opportunity to get that 10 x 22 metal lathe. I figure that bolt at about $1001.25 I have to pay for the stock after all!

Naw. I'll chuck up a hex rod in the drill press to file the corners and thread one end when they are gone.