Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Router Repair??

Posts

Router Repair??

#1

Router Repair??

Thomas Norton

>I have an old Black & Decker router from my father-in-law. It is the chrome housing kind. It has been showing a lot of sparking around the armature when it runs. Also the bearings need to be replaced but I can handle that. The sparking is my issue. I checked the brushes and they look OK.I guess.

Any thoughts? I really want to keep this tool.

Thanks

Re: Router Repair??

#2

Re: Router Repair??

Kneale Brownson..Awaiting return to CO snows

>Because of its age, it may have a turnable armature. I'd take it to an electric motor repair shop.

Re: Router Repair??

#3

Re: Router Repair??

GalenV in Iowa

>You say the brushes look OK you guess. More than likely they have worn short so they do not have enough spring pressure on them so they are bouncing when it runs. The commutator could now be rough from the arcing and in need of turning or just polishing as well.

If the bearings are bad they too can create the bounce at the bushes.

Galen

Re: Router Repair??

#4

Jesper, Denmark

Re: Router Repair??

Jesper, Denmark

>What Galen said and:

when you clean up or turn the commutator, find a hacksaw blade that fits between the metal parts of the commutator and clean out the insulation between the metal parts a little. The insulation should be just a tad lower than the metal. A tad is maybe a few thousands, just enough that you know it does not stick up above the metal.

Re: Router Repair??

#5

Re: Router Repair??

Tony - Memphis

>This all reminds me of generator repair tips in the book "How to Keep Your Volkswagen Running for the Complete Idiot." There were instructions on how to rejunvinate the generator by applying a popscicle stick with sandpaper to the (whatever that part is that the brushes ran against) to polish it up! Pardon my typing, my pc died and I'm using a forklift terminal for the moment!

Tony

Re: Router Repair??

#6

Re: Router Repair??

les winter

>Before you give up on the brushes, try removing each (note the orientation) and applying a blast of compressed air into the opening. It has worked for me before. While you are at it, shine a flashlight down the hole and inspect the copper bars. If they are all greenish or dark brown, you will need to clean them as well; a full dis-assembly job.

good luck.

les

Re: Router Repair??

#7

Re: Router Repair??

Thomas Norton

>Took the guts to a local motor shop. They put it on a lathe and polished the commutator.

I do need new bearings and a local bearing house gave me a price of about $40 for both. Would like to shop for bearings on line. Anyone have a source?

Thanks

Re: Router Repair??

#9

Re: Try Graingers

Robby Wright in San Marcos, CA

>They have most bearing types for a decent price. If you look on the side of the bearing, there should be a bearing number, something like 203. If you can find it, give them a call. Or you can measure the bearing and use their selector.

Re: Router Repair??

#10

Re: Router Repair??

GalenV in Iowa

>Thomas:

Don't go too cheap or if you do insure you are still getting the same quality bearing. You are looking at a high speed bearing and not what some just list as motor quality, which in most cases is 1725 rpm.

The bearing that was in my Jet live center was a 6002Z and has metal seals for high speed operation. What I get from the local machine shop is 6002 2RS or double rubber seals and are more for 1725 motor speed. They do not last as long but then I use the cheap Jet live center for out of balance rough blanks and then go to the better center when I have things running smoother. Like I think I am saving the expensive center by using the disposable $4 bearing center?

Don't waste your time using the old brushes on the newly turned commutator or you will just be back to the same place in a short time.

Galen

Galen

Re: Router Repair??

#11

Re: Router Repair??

Thomas Norton

>Thanks for all the responses. I will just go ahead and order the bearings from the bearing house and get some new brushes.