Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

First woodshop!

Posts

First woodshop!

#1

First woodshop!

Denis doiron

>Hi all,

I want to convert my detached two car garage (20X25) to a woodshop.

I will trying my hand at home furniture.

What do I need? Where do I get it? What should I buy new/used and where?

What would be a resonable budget?

Thx!

Denis

Re: First woodshop!

#2

Re: First woodshop!

Chuck in ND

>If you don't know what you need, how are you going to build it ?

Re: First woodshop!

#3

Re: First woodshop!

Will Abbott

>Do you have any experience with woodworking? If not I would start with taking some classes at a local school. Wood working can be a very dangerous hobby if you don't know how to use tools safely.

Re: First woodshop!

#4

Re: First woodshop!

Nat Robison

>You could probably get 100 different answers and opinions here but you could also find some good articles in some of the different woodworking magazines.

My opinion is to start with a tablesaw. You can build lots of basic furniture pieces with only that. Also, don't commit your entire garage to a shop just yet.....unless you're a pro, you probably won't need 500 sq. ft. I park my cars inside at night and have a tablesaw, router table, saw horses, dust collection etc. Finally, don't buy tons of tools to begin with. Find out if you like it and are decent at it, the tools will come shortly if you're decent.

Your question is a broad one. Be prepared for answers and opinions that are just as broad.

Re: First woodshop!

#5

You need all this, and more...

Bricofleur

>You need interest

You need passion

You need time

You need confidence

You need imagination

You need commitment

You need curiosity

You need inspiration

You need to learn

You need patience

You need to read

You need to know yourself

You need the humility to start at your own level

You need to work at your own pace

You need to practice, and practice, and practice

And last, you need to invest in all above.

Best,

Serge

http://www.atelierdubricoleur.spaces.live.com

Re: First woodshop!

#6

Ben Franklin is your friend

Bill Houghton, Sebastopol, CA

>2+ centuries after Ben Franklin started one of the first lending libraries in the U.S., they're still a vital resource. Go to your local library, check out every book you can find on workshops and beginning woodworking, and read through them all.

It's not at all a bad idea to start out with a few basic hand tools and make some very basic projects before you begin investing in big and expensive power tools. You may find you don't like it as much as you might have thought. Even if you do enjoy it, machines will never replace hand tool skills - you'll need them for refining what the power tools do - and using your own perspiration and cholesterol to cut the wood will give you a much deeper understanding much faster of how wood is put together.

Re: First woodshop!

#7

Re: First woodshop!

Stuart Hough

>Ditto on all that has been said before. From the perspective of someone who started out just as you are about to, I can give you the benefit of my experience, such as it is.

1.) Read EVERYTHING you can get your eyes on about shop setup and

woodworking.

2.) Look over the shoulder of someone who has been a woodworker and

is willing to answer all your questions.

3.) Stay with this forum. It has as its members many of the best,

brightest and most giving people in the world.

Last and probably the MOST important for your sanity and marrriage,

PUT EVERYTHING POSSIBLE ON WHEELS! You'll know just how much your wife appreciates your hobby when she DOESN'T have to clear the snow off her car! Please...don't ask why, just follow this sage advice!

Re: First woodshop!

#8

Re: You need all this, and more...

Barry Irby

>I agree. You need all of the above.

I have had tools for a workshop since I was about 15 and I am 60. I started with a lathe and A Radial Arm Saw (RAS). the RAS was because the woodworking mags at the time painted it as the "Does Everything Tool". (Now, not so much)

When I got out of college I bought a TS, Jointer, Shaper, and drill press. About twenty five years later I got over the lust for a 36" planer and bought a lunch box planer. Than a 14" bandsaw. Then a used Performax drum Sander. And Dust collection.

I would say that the planer was a turning point. I could finally dress my own lumber and make any thickness I wanted. The Dust collection was a major improvement too. I can't believe I operated those tools all those years without it.

To answer your questions, you have to decide what you are going to build and what you want to spend. If you are going to build furniture (Flat Work), I would start with a table saw as mentioned above. If my budget was flush, I would start with a Sawstop. (read the post below where we discuss the Sawstop vs non sawstop tools). If I were unsure of my commitment I or not flush with cash, I would buy a used TS. I Have a Delta contractors saw that is almost forty years old and I like it. As a hobbyist, it has done what I needed.

If you get bitten by the Turning bug, you will need a lathe and then perhaps a band saw and chainsaw for preparing the blanks.

There are multi-purpose tools out there that will do many things (ShopSmith) and others. I find the swapping of functions to be annoying and time consuming. (A feeling left over from the time I only owned the RAS). A friend has one and gets along fine with it. Most of these machines do one or two things well and a a serious compromise for the others.

So, Your question really is too broad, kind of like How high is up. There will be as many answers as there are member of the group. There will be any answers based on blind loyalty to specific brands. Ford VS Chevy Most of us have bought tools and used them and like or dislike them based on that experience. Generally we don't have the luxury of trying all the different brands over a period of time and dividing based on broad experience. I like my Delta tools. Most of my tools are Delta. Based on that, given a choice I would buy a Delta Unisaw over a Powermatic. Actually, I believe the Powermatic is just as good, but OTOH I like my Delta tools.

Re: First woodshop!

#9

Re: First woodshop!

Joseph Mulherin, Sr

>I agree with most of the posts. I bought the Shopsmith in 1978 and found it does all of the things that I need to do in making furniture....and I have made several pieces with it over the years. A new saw is rather expensive so I suggest you go to Ebay or Craiglist to find a good used saw near you for less money than new equipment and start with it for now. You can always sell it and get other equipment. Changing over from one operation to another is time consuming but if you schedule your work to do many operations in a particular mode it does prove to be a very good machine too have. It is on wheels, is about the size to cover a bicycle space room.

I bought a planer, bandsaw and router to use with it too... All in all, a very good machine to have for me.

Re: First woodshop!

#10

Re: You need all this, and more...

john lucas

>I have to agree with both of them. I started with a Router, jigsaw and handsaw. I built much of what I build today only it took longer. I had the passion and really enjoyed trying to figure out how to build something.

I now have a show full of tools and can build just about anything. If I was teaching woodworking I believe I would start with a bevy of hand tools and a good workbench. It is a much slower pace but you learn lessons that can be carried over to all the other furniture no matter what your budget.

If money is not a problem I would buy a good table saw, Bandsaw router and table, jointer, planer and drill press. With those things I could build jigs and cabinets and workbench for the shop which are very good starting projects.

Re: First woodshop!

#11

I sarted with . . .

steve mackay

>a copeing saw, hacksaw blade and pocket knife. Learned what else I needed along the way.

Re: First woodshop!

#12

Re: You need all this, and more...

gary peterson

>I didn't read all the responses, so I may repeat stuff here.

Great elec source, upgrade your panel. Position of outlets.

Great lighting.

Great dust collection.

The tools, et al. will come when you need them. Don't buy cheap.

Re: First woodshop!

#13

Re: First woodshop!

Myra

>Someone suggested that you might take a class. I would second that suggestion. Not only will it help with safety, it will help you learn if you really would enjoy woodworking - BEFORE you buy expensive equipment. Furthermore, you will be able to talk with the other students and with the instructor about equipment and needs.

If there is not a class nearby, for example at a community college, etc., there are week-long classes at various sites around the country. They may be expensive, but not as expensive as a workshop full of equipment that will see little use.