Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

A warning to TS users.....

Posts

A warning to TS users.....

#1

A warning to TS users.....

Barry Irby

>My friend makes kitchen cabinets for a living. Uses a ten inch TS. Was ripping some salvaged lumber that had splits in it. The saw threw a splinter that caught him on a finger. Went in one way and came out another. I have not seen the wound so I don't know the details exactly, but I gather the splinter traveled a pretty good distance through the flesh. He had pulled out the obvious part and was applying first aid when he realized it went through. Went to the doctor and they had to make an incision to get the rest of it.

Lets be careful out there. May not be wise to work with crappy wood.

Re: A warning to TS users.....

#2

Re: A warning to TS users.....

Bricofleur

>Thanks for the reminder Barry.

Best,

Serge

http://www.atelierdubricoleur.spaces.live.com

Re: A warning to TS users.....

#3

Re: A warning to TS users.....

charlie belden

>And it ain't wise to rip wood that isn't sound and

properly prepared. Crooks, bows, twists, cupping, checks and cracks can raise hell when doing rip cuts.

Re: A warning to TS users.....

#4

Re: A warning to TS users.....

Jim Toews - Walla Walla, WA

>Couple of years ago I had a similar thing happen with my router table. I had to route a small piece, so I clamped it between two hand screws and routed away with my hands a good 10" from the bit: the piece shattered and a wedge-shaped splinter was ejected at great speed and sliced off the end of my left index finger. Bled like a stuck pig. I was rather ticked off since I had thought I'd done everything right and I still got bit. Oh well, at least it was just the tip and I can still count to 9.95! We can't be too careful when using our tools, especially power tools, but even hand tools can bite if we don't pay attention.

Re: A warning to TS users.....

#5

Knots, too

Stephen Kirk in Quakertown, PA

>Gotta watch out for knots as well. Just yesterday I was ripping down some 2x10s and the few knots proved a bit troublesome. Some would shatter and fly out in bits. Go slow, pay attention, watch the cut and the board, use a splitter and definitely push sticks.

Can't wait to get a band saw and move my large rip jobs to it. Keep the table saw for smaller rips.

Re: A warning to TS users.....

#6

Any shop injury . . . . .

Alan in Little Washington (NC)

>Never ignore a shop injury!!

My local tree service guy and source of hardwood cut his finger on a piece of wood. When I saw him on Sunday he had a bandaid-sized cut and the pain was minimal, just a nuisance. Another friend reported the same when he saw him on Monday. Things started to go bad on Tuesay, however, but he waited to see a doctor until Wednesday. They admitted him to the hospital that day. . . . . unfortunately it was too late and this 42 year old man passed away on Thursday!!!! I never heard the full story, but suspect MRSA or some other deadly Staf type infection.

Re: A warning to TS users.....

#7

Re: Any shop injury . . . . .

Fred Davis

>One can't say enough about the dangers of MRSA or Community Aquired Staph infections.

I have had the problem for about last ten years of sometimes getting that after a splinter has made a wound.

So far Cephalexin takes care of it , but according to the Medics , the day is not far off when it will be bullet proof to present Antibiotics.

If you get a puncture wound , no matter how small and it becomes a hard red lump with a White center , get to the ER.

I consider this Organ attacking bug far more dangerous in the shop and elsewhere , then any lapse of attention around your machines.

One can get along with nine digits, but missing a Liver or Kidneys can be a real bummer.

FredD

Re: A warning to TS users.....

#8

That reminds me of one that got me.

Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6

>I was ripping some tomato stakes for my BIL. There was a split / ring-shake which crossed the wood at a slight angle near the end.

As I fed the wood into the blade, the back end was wedging under and between the fence, pushing the now free spear over onto the top of the blade.

That spear hit the end of my left index finger, and punched through to the bone. I am here to tell you, there are a heck of a lot of nerves in the tip of your fingers.

Re: A warning to TS users.....

#9

One upping the gore...and a safety suggestion

Bill Tindall, E.TN

>A woman working at a local shop running an inline rip machine ripping strips for a molding machine failed to wear the required leather apron. An arrow shaped cut off came off the saw and pierced through her abdomen. Miraculously missed all vital organs and spine.

Which is why I advocate using 71/2 or 8" extra thin blades on the home shop table saw(when possible, which is most of the time) They don't throw things with any scary force.

Re: A warning to TS users.....

#10

Re: I knew a guy who had the same thing and...

Brian in Brighton

>I also know a guy who was using his CS to cut shorts from the end of some oak and he was being dumb and holding onto the 3 inch offcut. The saw launched the piece off the stand. His hand didn't move but the freshly cut edge on the offcut tore the last digit off his left index finger. He found the piece on a shelf about 4 months later.

Brian in Brighton

Re: A warning to TS users.....

#11

8" blades

Simon St.Laurent - Dryden, NY

>I like the idea in general, and I guess I already have a 6" dado set, so I've thought a bit about it before.

Other than limiting the depth of cut, does it make much other difference to the cutting experience?

Thanks!

Re: A warning to TS users.....

#12

yes, its wonderful

Bill Tindall, E.TN

>This isn't my idea. I saw, year after yea, the person demoing the wonderful "Grip-tites (Mesa Vista Designs) by ripping thin strips using a small thin blade. Light bulb over head eventually illuminated and I tired it. I have kept a 7 1/2 blade, of some variety, on my saw now for almost 2 years. Other than the obvious depth of cut issue (limited to about 1 5/8") I have not found a 7 1/2" blade that delivers as perfect a cut as an optimized 10 " blade. That said, I rarely need a mirror smooth cross cut. I have, with care, ripped glue joint quality cuts with the small blades, especially on thin stock.

Advantages: ***They don't throw things.***I won't say they can't but I feel safe ripping thing with these small blades that would be scary with a 10" blade because I have never had one grab anything and offer to throw it. Quiet, don't make much dust, don't vibrate small or thin pieces during cut, almost no cutting resistance so control is easy.

I have used a variety of blades. The CMT so far has been the best quality, but for much work the quality is irrelevant so I tend to use cheaper blades. It probably is not worth resharpening these blades, but I have had it done.

Be sure you get a combination blade and not one optimized for miter saws. I use a 40 tooth blade.