Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Hollow chisel mortiser clogging question

Posts

Hollow chisel mortiser clogging question

#1

Hollow chisel mortiser clogging question

Barry Irby

>I have a half inch square chisel in my hollow chisel mortising attachment on my drill press. Even though I have only done about eight or ten mortises with it, it has always worked well. This time it is clogging. Puncihng 1/2" by 3'3 mortises 2 1/2" deep in old dry Osage Orange. Did about two of them and then the clogging started. Tried wax on the bit, seemed to make it worse. Cleaned, sharpened and polished everything except the inside of the chisel "tube".

How fast should I be running the bit? I may be running it too slowly, I think it is on one of the lower speeds.

Would graphite lubricant help?

Any suggestions?

Re: Hollow chisel mortiser clogging question

#2

Re: Hollow chisel mortiser clogging question

Lee Schierer - McKean, PA

>I would step up one speed to see how that works and make sure the clearance between the chisel and the back of the drill bit is the thickness of a dime. Do not use grpahite as it will cause finishing problems and generally make a mess. I would recommend honing the outside of the chisels to get an extremely smooth finish, which will make them cut better and pull out easier.

Lee

Re: Hollow chisel mortiser clogging question

#3

Re: Hollow chisel mortiser clogging question

Fred Davis

>Your trying to make the chisel do something it can't, namely drill deep holes in Osage Orange , one of the hardest woods to cut and not with the steel your bit is made of.

FredD

Re: Hollow chisel mortiser clogging question

#4

Re: Hollow chisel mortiser clogging question

Larry Clinton At Frankfort (Central)., Indiana

>I have found that if I use the blade and bit spray lubricant - I think it's called "Dricoat" - the bit runs much cooler and clears a whole lot better.

Re: Hollow chisel mortiser clogging question

#5

Re: Hollow chisel mortiser clogging question

Phil Joines Krum,Tx

>Fresh cut Osage isn't all that hard. From the pieces I've used it starts to get hard after 2-3 years.

Re: Hollow chisel mortiser clogging question

#6

Thanks, We have success

Barry Irby

>This osage was cut about five years ago and has air dried out doors for about four. Then we cut the legs blanks and tapered them and they "rested" indoors for about a year. They are 3 1/2" square at the top and about 1 3/4" square at the floor and 29 inches long.

Thanks Lee and everyone else for the help. I used the dime trick (Looked it up on YouTube, Ain't it great) to set the clearance on the bit and chisel. I had sharpened and polished it with a diamond hone. Jacked the speed up one notch on the DP and everything worked as it should. Also blew the chips out with compressed air each time we withdrew the bit. Not sure it was necessary, but it seemed to help.

And, yes you can punch a half inch bit into osage, but your arm might come out of the socket. I let my son do that part.

Re: Hollow chisel mortiser clogging question

#7

Re: Hollow chisel mortiser clogging question *LINK*

charlie belden

>As noted, getting the chisel/bit gap about right can save you a light of grief. And if you're a Visual Learner - the illustrations on the attached page about the Forty Cent Method of setting the chisel and bit may help.


Forty Cent Method

Re: Hollow chisel mortiser clogging question

#8

Re: Thanks, We have success

Fred Davis

>Barry, just because you managed to force the chisel to punch the hole doesn't mean your doing your Chisel any favors.

What you can do in difficult woods and doing it will extend your Chisel life, is hog out the majority of the wood in the mortise with a drill a little smaller then the Chisel.

Drills are much harder and much less expensive then a good Mortise Chisel.

I routinely do this with a dedicated Mortiser made by PM and I use Clico Chisels and I take care of them because they are expensive and do better, faster work when they are maintained and helped along with pre-drilling.

Osage Orange besides being very hard , is abrasive.

Also is subject to splitting when you least expect it.

Makes great firewood though, about 200.00 dollars a year of it split and delivered gets us through the Winter.

FredD

Re: Hollow chisel mortiser clogging question

#9

You are right....

Barry Irby

>I have had this drill press and mortising attachment for almost forty years. Bought it soon after I got out of college. Life got in the way and I never used the mortising attachment until a couple of years ago. If any instructions came with it, I don't know where they are, even though I still have all the paperwork that came with the machine. So, about a year ago I punched some mortises with this same chisel in walnut. Eight, in a set of table legs. Now eight more.

I have used the smaller bits, 3/8" and 1/4", about the same amount. So, after resting in the drawer for about thirty five years, they have gone from doing nothing to working at a maniacal pace. The bits are complaining. They thought they were in retirement by now and here they are having to work.

I did consider drilling away much of the stock with something, perhaps a forstner bit, but since I am making it up as I go along, I did not know whether that would affect the accuracy of the work.

For future reference, Can you describe how you might drill out the stock? I can see drilling half inch holes, leaving about a 1/4" between them and then cleaning out the "webs" with the hollow chisel. Or would you use a smaller bit?

Thanks for the help.

Re: Hollow chisel mortiser clogging question

#10

Use a forstner bit...

Grant in Iowa

>I often use a forstner bit for rough stock removal in mortises. Set up a fence on your Drill press and drill away. So long as the center spur on the bit is in undrilled wood, you can drill overlapping holes.

Regards,

Grant in Iowa

Re: Hollow chisel mortiser clogging question

#11

Re: Use a forstner bit...

Fred Davis

>Grant's post about using Forstner bits is fine as far as it goes , but a good grade of Forstner is costly and in difficult woods like Osage Orange will have the same problem your Chisel bit is having, namely it can't get rid of the heat fast enough and will turn blue on you and ruin the bit.

I have done so many MT joints, that I really don't think about the process , but here is what I do.

Layout out the Mortise accurately , using a Machine spur bit, often called a Brad point bit, I would chuck a 3/8ths bit for hogging out the waste in a half inch wide mortise.

There are a couple of tricks to getting smooth absolutely vertical holes for both ends of the Mortise.

Being right handed I cut the first hole in the right end and the second hole in the left end of the mortise, these two holes will be vertically true because the bit is surrounded on all four sides and cannot flex.

Then return to the first hole and start drilling using overlapping holes as you go.

The second part of this procedure allows the chips to fall away in the area already drilled and so won't interfere with your view.

All of the above is made easier with a MT machine rather then a drill press attachment , especially the added leverage you get with a MT machine verses the Drll press.

I see the power bore bits being offered by Rockler and others that are designed for rapid chip removal and this would seem to be the best bit for hogging out the waste ,though I have not had a opportunity to try them yet.

If you do a lot of MT joints , you will get to like doing them , especially if you buy a machine made to do them.

Some of the projects I have done in the last year or so had forty to fifty MT joints and that is a lot of pulling down on a handle.

Lastly I keep a air hose with blower tip hooked right on the machine and clean out the Mortises as I go.

FredD