Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Epoxy glue & WD 20 question

Posts

Epoxy glue & WD 20 question

#1

Epoxy glue & WD 20 question

North of the Border

>Does WD 20 interfere with the gluing action or affect the strength of epoxy glue? For example, if one piece of a wood is sprayed / soaked with WD20 but is then allowed to dry (evaporate?) completely before it's glued to another wood piece using epoxy glue, will the joint fail?

Re: Epoxy glue & WD 20 question

#2

How much is that in American Money?

Neal in San Jose

>Down here in the South 48, it's WD 40. I'd be surprised if it didn't weaken the glue bond significantly.

Re: Epoxy glue & WD 20 question

#3

define "completely"

Bill Tindall, E.TN

>Obviously if the stuff is completely gone it will have no effect. I am doubtful it will ever be completely gone, and hence it almost certainly will affect the bond. A simple test gluing will test the theory.

Re: Epoxy glue & WD 20 question

#4

Re: Epoxy glue & WD 20 question

Rich F.

>Short answer I think is that the WD 40 / WD 20 will definitely affect the strength of the joint. But I also think the following:

When the WD 40 'evaporates', the solvent part evaporates and leaves behind the oil (lubricating) residue. What you want to do is remove as much of that residue as possible from the pores of the wood, prior to epoxying, so that the epoxy can get into the pores and bond. So cleanup/soak the WD 40-contaminated wood as much as you can with a volatile solvent that cuts that residue (like mineral spirits/paint thinner/lacquer thinner), then press paper towels or similar against the surface to soak out as much as you can by capillary action. Let it dry for a day or two - depending on humidity and wood density. You may have to repeat. ...Depending on how much WD 40 is soaked in, of course, you should be able to pull out enough to get a decent bond.

Boat restorers have to pull out old fasteners that are lubricated, then re-epoxy that wood. You could go on one of the wooden boat web sites and ask them.

But I think that you should be able to do this, assuming that the boards aren't fully soaked with WD 40, and that they have just been sprayed a bit (--for example, to loosen a fastener.) If you have the proper solvent, and enough solvent, and patience, you can cleanup almost any lubricant contamination.

Good luck. ...Your actual success may vary depending upon your own epoxying habits.

Re: Epoxy glue & WD 20 question

#5

Re: Epoxy glue & WD 20 question

john lucas

>As someone who has had to clean WD-40 off of things that never should have seen it(cameras and such), I can tell you that all of it doesn't evaporate. I've had good success cleaning if off of metal with most any solvent but I've never tried wood.

My question is, why did you spray it on wood? I do photograph for a lot of glass artists who spray it on sandblasted glass to increase the luster but I haven't seen anyone use it on wood.

Re: Epoxy glue & WD 20 question

#6

Re: THANKS for all the advice it's WD40

North of the Border

>I don't know why I was thinking WD 40 but typed in WD20! The reason I asked this question was someone used a piece of my board as the backboard when he sprayed WD 40 on a gear (about a week ago). The board looked stained but dry to touch. I was wondering if it was ok to use the board instead of throwing it away.

Re: Epoxy glue & WD 20 question

#7

Ellis Walentine

Short answer: Heave it.

Ellis Walentine

>I wouldn't stake my reputation or even my comfort level on a glue up on material that had been contaminated with a lubricant. They're designed to keep things from sticking. If it's truly a do-or-die situation, you could plane the contaminated surface until you think you are past the contaminated layer and glue it up with reasonable confidence.

Ellis