Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

preserving unused varnish

Posts

preserving unused varnish

#1

preserving unused varnish

Jeff

>Is there a way to save varnish and minimize or eliminate the skin that forms inside a sealed can?

I've been fanatical about keeping my lid clean to ensure a good seal.

Knowing that exposure to air is what causes the skinning, I tried placing some plastic wrap on the surface of the varnish inside the can. The only thing this did was to make it easier to remove the skinned varnish before my next usage.

With this whole exposure-to-oxygen thing in mind, I seem to recall a product called Bloxygen that one could spray into a can of finish before sealing it up. Bloxygen would displace the oxygen in the can. Anyone ever tried this product? The concept of Bloxygen got me thinking, though: if you're trying to remove oxygen, then would shooting a bunch of propane into the can prior to sealing it also work?

Maybe this is just the nature of the beast. It's just frustrating to have to spend a couple minutes straining the varnish every time I have to use it.

Thanks for the advice,

Jeff

Re: preserving unused varnish

#2

JL

Re: preserving unused varnish

JL

>Bloxygen works quite nicely. It consists of argon, an inert gas that has an atomic weight of 40. Air is a mixture of nitrogen, oxygen (and a lot of trace stuff) and weighs (on average) about 29-30. Argon (Bloxygen) displaces the air and is trapped quite nicely in the container.

Can you use propane? Sure - it will displace the air. It weighs about 44. You can also use carbon dioxide which weighs 44 also. Of the two, I would prefer using carbon dioxide - it is much less flammable :). I have used both for long term storage. You can get a CO2 canister from a bar supply place. I have used marbles to fill up a can and minimize the headspace above the liquid. My personal preferences are: Bloxygen, CO2, marbles and finally propane.

YMMV - but I would use CO2.

Re: preserving unused varnish

#3

My "brilliant" propane idea

Bill Tindall, E.TN

>I thought, because oxygen causes paint and varnish to spoil, and I'm frugal, I'll displace the oxygen in a can with propane and preserve the paint. What a brilliant idea! I already had visions of posting it on WoodCentral and basking in the accolades.

It was a good idea for a day or so. But as the propane dissolved in the paint solvent a vacuum was created in the can. The picture shows the result of this less than successful idea.


img

Re: preserving unused varnish

#4

CO-2

Mark Mandell - Gone Round In Jersey

>In a long-neck empty clean beer bottle, mix 3 tbls. of baking soda with 1/3 cup white vinegar with a loose cap. When the bubbling stops you'll have most of a bottle full of CO-2, which you can carefully pour into your varnish can to displace the 18% oxygen atmosphere in the can. Then apply your lid to seal and,

here it comes . .

Store the can upside down.

Even if there is some oxygen still in the can, the heavier CO-2 will form a layer on top of the liquid preventing most of polymerization that forms the skin. You will have to do this each time you open the can, and it won't prevent the polymerization of the oil while you're drawing from the can, but it will extend the shelf-life of your varnish. I use this with Waterlox, both red and green, and it has enabled me to get far more (but not all) from a can than usual. Way cheaper than Bloxigen as well.

btw, I have a bag of marbles if anybody wants'em. You pay shipping.

Re: preserving unused varnish

#5

not correct

Bill Tindall, E.TN

>Store the can upside down. Even if there is some oxygen still in the can, the heavier CO-2 will form a layer on top of the liquid preventing most of polymerization that forms the skin.

There is benefit to storing the can upside down. Any tiny air leaks in the lid will seal by the leaking and then polymerizing varnish/paint.

The carbon dioxide layer theory is not correct. Gases and vapors will begin to mix in seconds on the scale of a paint can head space. These molecules are not sitting still in the can. They are randomly zipping around at a speed that depends on their temperature. If we start a race with some carbon dioxide at the bottom of a tube and oxygen at the bottom of another, at 32 degrees F the carbon dioxide molecules will travel( diffuse) 9 inches up the tube in a minute and oxygen will travel 10 inches. These rates ensure that the gases and vapors in the paint can head space are mixed in a matter of minutes.

Re: preserving unused varnish

#6

Okay,

Mark Mandell - Gone Round In Jersey

>Then I guess I've been filling the can with CO-2 because I get no skinning of the liquid's surface, even after months on the shelf unopened. I'll not argue with Mr. Boyle, but I will state my result and draw a reasonable conclusion. If there were significant oxygen making contact with the liquid, a skin would form, so, discounting my ability the displace all the "air" with CO-2 (especially since I can't test the space), I inferred that a layer had formed with the can sitting on the shelf.

Re: preserving unused varnish

#7

Re: preserving unused varnish

Thomas S Stockton------WebKitFormBoundaryRU4sWQOIA

>You can also get bloxegen at wine stores, sold to preserve wine. Same exact can with a different label and name. Sorry I don't remember the name.

Tom

Re: preserving unused varnish

#8

But

Mark Mandell - Gone Round In Jersey

>since no layer formed, there must be little or no oxygen present to contact the liquid.

Re: preserving unused varnish

#9

A Truely Crushing Experience, Bill

George@Colonel's Workshop-Havertown PA

>

Re: preserving unused varnish

#10

Re: My "brilliant" propane idea

Stuart Hough

>At least you know you sealed the can up tight!

Re: preserving unused varnish

#11

Re: preserving unused varnish

Alan in Little Washington (NC)

>If it is a polyurethane based or poly blend "varnish" you're out of luck. If oil based "varnish" bloxygen etc. will work.

Re: preserving unused varnish

#12

Yeah but, was the varnish still good?

Barry Irby

>Don't be distracted by the obvious. Use a vacuum resistant container and you might have something. Try one of granny's canning jars. Of course, my Granny would have whacked me on the head for wasting one of her jars. Vacuum packed varnish?

Wonder what dissolving propane into varnish does to the product?

Re: preserving unused varnish

#13

Re: Yeah but, was the varnish still good?

Bill Tindall, E.TN

>Wonder what dissolving propane into varnish does to the product?

I would not suggest smoking while applying. Other than that issue...nothing.

Re: preserving unused varnish

#14

Water bottles

Bill Hammond, Oregon Coast

>I will pour the unused finish into a water bottle and squeeze the bottle until there is no air left in it. The clear bottle lets me see if it's doing strange things inside. As I most often use quart size cans I will let the can dry and put the bottle inside it and place it on a shelf, that way I know what's inside. If it's a squeeze top bottle you can use it out of the bottle if you are padding a finish. Haven't tried this with lacquer, not sure what it would do to the plastic but varnish, poly, shellac and the like work fine thus far.

I expect there is a fire issue if you have a lot stored like this.

Bill