Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Corner clamps?

Posts

Corner clamps?

#1

JL

Corner clamps?

JL

>I've got several Pony corner clamps (and one old Stanley).

Eventually we are going to have a "flat" building session over at the theatre. We typically take 1 x 3s (or 1 x 4s) and make a rectangular frame that is either 4 x 8', 4 x 10' or 4 x 12'. We then put a skin of 1/8" lauan on the face side and put triangular "keystones" on the back side.

I am trying to build up the tool supply at the theatre. So I was thinking of ordering several (4-6) clamps to use in making these flats.

I have been using my old Pony clamps as they are a reasonable size for 1 x 3s. The jaw capacity of the Pony clamps is 3" - which means you can't use a Pony to square up a 1 x 4.

What is a good inexpensive alternative?

TIA

Re: Corner clamps?

#2

Re: Corner clamps?

Bill Houghton, Sebastopol, CA

>I assume you mean the picture frame type clamps. These are useful for small assemblies.

Could you screw short lengths of 1x3 or 1x4, at right angles, to a plywood base and then use any two available clamps (c-clamp, bar clamp) to clamp the set framing members to the right angle you've made?

Re: Corner clamps?

#3

Re: Corner clamps?

Kneale Brownson..Awaiting return to CO snows

>I've been using the corner brace devices pictured, thanks to McFeeley's website, with whatever size bar clamp is required to hold 1- and 2-by whatever width stuff to make up corners.


img

Re: Corner clamps?

#4

JL

Re: Corner clamps?

JL

>Ok - that looks like it will work. But the clamp cost will drive it up. I'll have to include it in the budget.

Re: Corner clamps?

#5

Re: Corner clamps?

Kneale Brownson..Awaiting return to CO snows

>You could do as Bill says, mount scraps of, say 2X4 to scraps of something flat like OSB to form a square corner. Then your only expense will be the bar clamps. These, again from McFeeley's website, are $5-8 each.


img

Re: Corner clamps?

#6

Re: Corner clamps?

Barry Irby

>JL, I am unclear on why you want clamps at all. Why not just lay out the pieces of the flat on the floor and staple the corner blocks on and flip the flat over and skin the front?

If you really need clamps, you could make some homemade ones. Some plywood corner brackets that fit loosely. Then use wedges to snug up the pieces. You could make fifty out of a sheet of plywood.

Re: Corner clamps?

#7

JL

Re: Corner clamps?

JL

>The ability of some people to make things out of square astounds me, that is why :). We use a lot of volunteer labor at a variety of skill levels. Some of them I would trust.

I figure if I give them corner clamps, then at least the frame will line up with the lauan skins.

Re: Corner clamps?

#8

Re: Corner clamps?

Barry Irby

>Oh, I agree. The ability of volunteers to do something odd is astounding. I volunteer with Habitat and some of the stuff I see there is hysterical.

If I understand what you are doing, I would actually use the skin to square the frame. Doesn't that work for you?

Re: Corner clamps?

#9

JL

Re: Corner clamps?

JL

>Normally it does, but usually I like to put the skin on a "squared frame. If I have something to secure it (such as a corner clamp), I can just put a skin on and use 7/8" screws to secure the skin to the frame. I can then flip it over and put the "keystones" in the corners.

If everything is butted up really tight, there is less flex in the frame. I don't like using corrugated nails as I often have to modify a flat later. Circular saw blades don't play well with corrugated nails.