Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

OT - Briggs and Stratton 7hp. Won't start

Posts

OT - Briggs and Stratton 7hp. Won't start

#1

OT - Briggs and Stratton 7hp. Won't start

Joe in a Cleveland Suburb

>Please help. I've just about had it.

My Craftsman 7hp Briggs and Stratton mower WILL NOT START!

It's only a few years old. The problem started last year. I took it to a local small engine repair place, they did some stuff to it, took my money, and it worked ok (meaning it sometimes started) for a little while. Now it won't start at all.

The spark plug looks okay.

It gets spark.

It's getting gas.

It has oil.

I've checked all the obvious things.

It won't even start using starting fluid.

On the rare occasion it almost starts, it chugs, backfires, blows smoke, and never starts.

In the 80's I built Alfa and MG motors for my race cars. I can't figure out these stupid little engines though...

Any suggestions on anything I can check before I take it to a (different) small engine shop?

Thank you.

Re: OT - Briggs and Stratton 7hp. Won't start

#2

Re: OT - Briggs and Stratton 7hp. Won't start

Bill White

>Sounds like the timing has slipped. Sometimes the key holding the flywheel will get "squished" or otherwise allow the flywheel to slip on the crankshaft thereby knocking the timing out of whack. Look at that next. Remember:

Ignition, fuel, compression = running.

Bill

Re: OT - Briggs and Stratton 7hp. Won't start

#3

Joe Bradshaw

Re: OT - Briggs and Stratton 7hp. Won't start

Joe Bradshaw

>Pull your flywheel and check the key. Odds are it has began to shear.

Re: OT - Briggs and Stratton 7hp. Won't start

#4

Concur

Bill Houghton, Sebastopol, CA

>If I recall correctly, whether your motor has points ignition or, more likely, electronic ignition, the flywheel determines when the plug fires. The keys that position those flywheels are of extremely soft steel and shear very easily. The times it's happened to me, the key didn't shear all the way - rather, one half was offset from the other, resulting in several degrees of wrong timing.

Like a one-cylinder motorcycle, they're really very simple...yeah; and just like a one-cylinder motorcycle, if everything's not Just Right, they're somewhat greasy boat anchors.

Re: OT - Briggs and Stratton 7hp. Won't start

#5

Re: OT - Briggs and Stratton 7hp. Won't start

Bill Houghton, Sebastopol, CA

>I think, if the flywheel gets the least bit loose, or if you apply a lot of physical shocks to the motor - say, mowing dense high grass with occasional hidden shrubs in it - that it can apply a lot of pressure to that little key. It's a deliberate weak link, I'm sure. 25 cents or whatever they're charging for a replacement key beats rebuilding the whole motor.

Re: OT - Briggs and Stratton 7hp. Won't start

#6

Re: OT - Briggs and Stratton 7hp. Won't start

Dale Stansbery

>I agree that it sounds like timing, but if that checks OK, then I'd suspect sticky valves, especially if it's OHV, I don't know though if B&S made OHV's in 7 HP..

Re: OT - Briggs and Stratton 7hp. Won't start

#7

Re: OT - Briggs and Stratton 7hp. Won't start

Joe in a Cleveland Suburb

>Thanks for the replies. I'm going to go with your suggestions.

I'll let you know how it goes.

Thanks!

Re: OT - Briggs and Stratton 7hp. Won't start

#8

Don't forget the obvious

Dustmaker Mike

>the air cleaner. My push mower did this in July and it drove me nuts for about an hour. Just something else to look at.

Re: OT - Briggs and Stratton 7hp. Won't start

#9

Re: Don't forget the obvious

Kneale Brownson..Awaiting return to CO snows

>The other obvious is the condition of the fuel. Today's fuels are deteriorating after about a month. You may have fuel delivered through the carb that won't fire because it's degraded if it's been sitting in a can since spring.

Re: OT - Briggs and Stratton 7hp. Won't start

#10

Jim DeLaney, Austintown, Ohio

Re: Don't forget the obvious

Jim DeLaney, Austintown, Ohio

>Interesting ovservation, but I'm not sure it's true.

I use Stabil in every fuel can - I put it in the can before I fill it up. I've never had a problem with fuel deterioration.

I just got the leaf shredder out last week. I hadn't used it since last Fall. Poured some new fuel in on top of the quarter tank still in it, and it started on the third pull.

Same thing with the rototiller - not used since last Spring, but started on the second pull.

The generator gets cycled monthly, but the fuel in the tank is at least six months old. It always starts on the first pull.

YMMV...

Jim D.

Re: OT - Briggs and Stratton 7hp. Won't start

#11

Re: Don't forget the obvious

Joe in a Cleveland Suburb

>Thanks Kneale for the idea.

The fuel is fresh. Air cleaner is good too.

Re: OT - Briggs and Stratton 7hp. Won't start

#12

UPDATE

Joe in a Cleveland Suburb

>I just took everyhting off the top of the engine and exposed the flywheel. I can see the key in the slot and it apprears tight and looks like it has never moved.

I would need to buy a gear puller to remove it. Not sure what I would gain by removing it though. I have no idea whatever happened to my gear puller. I remember having one.... don't you hate lending out tools?

It is an overhead valve engine if that matters.

Anything else you engine guys can suggest?

Thanks a ton!

Re: OT - Briggs and Stratton 7hp. Won't start

#13

Re: OT - Briggs and Stratton 7hp. Won't start

del schisler

>before i read the other responce Here is what happen to me yrs back The fly wheel key sheared 1/2 off Not all the way Which ment timming was off ??? of course still spark but it was probly on the down cycle and not on the up cycle or before top center check that key just a thought

Re: OT - Briggs and Stratton 7hp. Won't start

#14

Re: UPDATE

Bob Entwisle in NJ

>How's the compression? Everything tight? carb to manifold, etc.?

You said it's getting fuel, I presume evidenced by a soggy spark plug after a no start episode?

That it won't start with starting fluid leads me to think no spark or no compression, maybe a hung valve?

Re: OT - Briggs and Stratton 7hp. Won't start

#15

pull fly wheel off key shears on crankshaft

del schisler

>the key still looks good from what you can see the key sheers from the slot in the crank shaft which when you look at it from the fly wheel it look's fine ??

Re: OT - Briggs and Stratton 7hp. Won't start

#16

ANOTHER UPDATE

Joe in a Cleveland suburb

>Here is a shot of the shaft & key.

Thanks for any further input.

Joe


img

Re: OT - Briggs and Stratton 7hp. Won't start

#17

fuel life

Bill Houghton, Sebastopol, CA

>Without stabilizer, gasoline will last for, at most, a season before it begins to turn. I learned that lesson when I paid a shop $50 to fix my chainsaw when I could have fixed it myself by draining the fuel before putting it away for the winter, and buying fresh fuel when I needed it.

We go through enough fuel in the lawnmower and four-stroke weed frightener (aka weed whapper) that I don't put stabilizer in the four-stroke fuel can; but, for the chainsaw (and, if I ever get it running again, the big, two-stroke weed whapper), I buy gasoline in quart quantities and recycle anything old enough that I can't recall in which month I bought it.

Gas stabilizer is, indeed, a great help.

Re: OT - Briggs and Stratton 7hp. Won't start

#18

I seem to remember a key on

Dustmaker Mike

>the blade shaft. It has been awhile but isn't there a key on the blade shaft that also shears if you hit a large object? Or was that just the old riding mowers?

Re: OT - Briggs and Stratton 7hp. Won't start

#19

But that shouldn't affect the motor starting

Bill Houghton, Sebastopol, CA

>

Re: OT - Briggs and Stratton 7hp. Won't start

#20

Re: OT - Briggs and Stratton 7hp. Won't start

Paul Leuba - Hunt Valley, MD

>I recommend that your next step be a compression test. A sticky valve or a broken piston ring are possibilities at this point.

Paul in Hunt Valley, MD

Re: OT - Briggs and Stratton 7hp. Won't start

#21

Re: UPDATE

Dan Donaldson

>How about the points?

Re: OT - Briggs and Stratton 7hp. Won't start

#22

Re: Choke ?

Chuck in ND

>Is the choke fully closed before attempting to start it ?

Re: OT - Briggs and Stratton 7hp. Won't start

#23

Re: OT - Briggs and Stratton 7hp. Won't start *LINK*

GalenV in Iowa

>Joe

You did not give any reference to the engine series and model. The link is to just one 7 hp but it has electronic ignition and a mechanical compression release. Is this even similar?

If you have your old service info what did they indicate they did to it last time? Might give a clue to problem.

Most of the posts are typical things that it might be that you are finding items seem to check out OK.

Not sure how they handle compression release for easy starting but if it kept it open probably would not run.

No owners manual to give manufactures trouble shooting ideas?

I have had spark on small engines but not hot enough to fire across plug.

If it has a resistor type plug it could have burned a gap inside. It would still fire but because of gap would throw off timeing. You might try a new plug.


Similar engine?

Re: OT - Briggs and Stratton 7hp. Won't start

#24

Hey Joe!

Lee Schierer - McKean, PA

>There are two keys you need to look at. One is the key on the flywheel, which you've already checked. The other is the key on the blade holder. If either key is sheared or partly sheared the mower won't run right. Years ago I bought a lawn mower at a yard sale and the owner said it didn't run right. It seemed to have good spark and plenty of compression. I took it home, pulled the blade off and discovered a sheared key. I put in a new key and the mower started on the first pull. I ran that mower for many years before the body rotted out.

Next check the valve stem clearance on the lifters. If the clearance is too tight, the compression isn't there for the engine to run. Reset the fuel mixture screws to the specified settings.

Lee

Re: OT - Briggs and Stratton 7hp. Won't start

#25

Thanks Lee and...

Joe in a Cleveland Suburb

>all. I have a number of things to look at.

Thanks for all the help.