Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Varnish Questions

Posts

Varnish Questions

#1

Varnish Questions

Brian in Brighton

>I recently completed the walnut mantle that I wrote about a couple months ago with the bleaching question. I have another one.

I brushed a coat of interior Benjamin Moore Varnish onto it and was getting ready for the second coat and stopped. I have some debris in the varnish that I can remove easy enough. But the varnish was pterry thick brushing and cured quickly enough that you can clearly see the dividing areas from one brushing zone to the next. Varnishing the underside was a real chore and I got a few drops that backed up the brush.

My question 1 is this. Can I sand with 400 grit and then thin the rest of the varnish 4 parts varnish to 1 part mineral spirits and then wipe on the next coat?

Question 2: I want a matte finish when I'm done so I plan on using 0000 steel wool on it, like I did on the columns next to the mantle last year. How long should I wait before I do this?

Thanks,

Brian in Brighton

Re: Varnish Questions

#2

Re: Varnish Questions answered

Glenn Madsen near San Francisco------WebKitFormBou

>1) yes, you can thin. VMP Naptha, or good mineral spirits should work. You could go a little heavier on the thinner, too, and not hurt any thing.

2) I'd wait a good 24-48 hours before sanding, maybe more. You want it cured hard. If the paper clogs, then wait longer. The thinned wiped coats, not as thick, cure faster and level better. They don't build as fast.

Re: Varnish Questions

#3

thinning varnish

Bill Tindall, E.TN

>Now days varnish is formulated to pass EPA regulations for VOC's and not for success in application. (editorial:Close your eyes an imagine the fraction of VOC contributed by people varnishing stuff. ) The result is that the solids, and hence viscosity, is higher than optimum for brushing. It is a good bet that any modern varnish will need thinning, about 20% in my hands, for good brushing or spraying. I have one woodworker friend that heats the varnish to achieve the same thinning result, but I find heating flammable substances somewhat worrisome.

I always plan on sanding the first coat of varnish. I am convinced that crap spontaneously materializes on a freshly varnished surface. Use about 280-360 stearated paper (the white stuff) or 0 steel wool.

It is hard to say how long to wait before sanding. If it is hot and dry maybe a day or two. If it is cold and wet, it could be long time. To be on the safe side I would wait a week beofre final rub out.

Re: Varnish Questions

#4

Re: Varnish Questions

Fred Davis

>Curing between coats of Varnish brushed on , can easily take two or more weeks to be hard enough to sand without undue loading of the Wet or Dry. Wet or dry paper is the recommended paper to use on Varnish.

The stearated paper Bill mentions is loaded with Zinc Stearate to fight loading of the paper .

This also makes it a poor choice for use under or between coats of a finish for the same reason, it will fight good adhesion from one coat to the next.

If you can easily press a finger nail into the Varnish , then it still needs to cure.

The modern Varnish dries a lot faster then the older formulations , but there is a distinct difference between dry to the touch and cured ready to sand or rub out.

The traditional way of rubbing out the last coat of Varnish was for years Pumice and Rottenstone sprinkled in Paraffin oil and rubbed with a felt block , like a blackboard eraser.

Still is a good way , but your 0000 steelwool used with paste wax will do fine.

Heavily thinned Varnish used for wiping , sometimes combined with Boiled Linseed oil; and Turpentine goes on fast , dries fast and needs many more coats to approach the thickness of a three coat brushed Varnish.

All of that said , let your Varnish get really hard , sand it down until you have a uniformly dull finish , carefully apply another coat with a little thinner added , cure and rub out.

Wax with a good finish wax , like Minwax finishing Wax, buff and your done.

You should have a finish slick as glass, regardless of the sheen .

FredD

Re: Varnish Questions

#5

Re: Sanded last night

Brian in Brighton

>So I sanded with 400 grit last night. Using the ROS I got some small balls of varnish that seemed to grow everywhere. I hand sanded the details and that filled the wet/dry pretty fast. I then wiped the whole thing down with mineral spirits, lightly. I'll thin the varnish in the rest of the can and wipe it on this weekend and let everyone know how it went.

Brian in Brighton

Re: Varnish Questions

#6

Re: Sanded last night

Fred Davis

>"I sanded with 400 grit last night. Using the ROS I got some small balls of varnish that seemed to grow everywhere. I hand sanded the details and that filled the wet/dry pretty fast."

Brian , I know I am unclear at times and this may be confusing occasionally.

What I really meant and should of said , "is your Varnish is as green as a Gourd and meddling with it before it is cured makes things worse.

Power sanding is even worse ,though I guess you could have used a belt sander.

FredD

Re: Varnish Questions

#7

Re: Sanded last night

Glenn Madsen near San Francisco------WebKitFormBou

>Fred's right about power sanding, and it was too soon. But it's too late to fix that now.

May I suggest that you do your varnish thinning in a plastic squeeze bottle, and use only a portion of your remaining material? Your measurements need not be critically exact. It is, however, difficult to take thinners OUT of a can of varnish. DAMHIKT.

The squeeze bottle is cheap, and helps greatly with the application of a wiped finish coat.

Re: Varnish Questions

#8

Re: Sanded last night

Brian in Brighton

>Actually the light sander didn't seem to disrupt anything, the little balls of varnish blew out the sides of the paper. I didn't notice that the finish had any issues. I'm putting another wipe on this weekend. I have some bottles from Hobby Lobby, so that will make it easier.

Brian in Brighton

Re: Varnish Questions

#9

Re: All went well

Brian in Brighton

>I thinned the varnish in a squirt bottle and was able to put a second coat on easily. It still shows brush/wipe marks very clearly, but they should come out with the steel wool/wax next weekend.

Thanks for the input gang!

Brian in Brighton, I'll post pics when I'm done.