Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

OT: Electrical DC ??

Posts

OT: Electrical DC ??

#1

OT: Electrical DC ??

Craig in Silverdale

>My cabin in the mountains is off grid. I have a solar cell (120W) and 4 Golf cart batteries. I do have an inverter(sine wave) I use for my computer. I try to use 12v items when I can. I recently found an L.E.D. light at Ikea and would like to use them for a reading lights above the bunks in the bedroom. It has a converter in the plug. But it has a constant output of 8.5V. I'd like to wire it into my system. Is there a simple formula for dropping the voltage from 12 to 8.5 Volts? Does this require a step down transformer or can it be done with a resistor?

Re: OT: Electrical DC ??

#2

Re: OT: Electrical DC ?? *LINK*

Bill Earl

>Is it a single high-power LED, or multiple LEDs? Is there any other circuitry in the lamp besides the LED & the switch? LEDs need a constant current which can be achieved by a stable voltage source & a resister, or (more reliably) by a constant current driver circuit.

If it has a constant current driver already, it *might* be able to run from 12V, but depending on the design of the driver, it could overheat.

If you know the characteristics of the LED itself, you can calculate the resister required to drive the LED directly from your 12V source.

Or you can wire in your own driver such as the one in the link below. Measure the current the LED is pulling now and choose the appropriate size.


LED driver

Re: OT: Electrical DC ??

#3

Re: OT: Electrical DC ??

John McGaw

>The biggest question is "where is the current controlled?" LEDs are components which, given the chance, will pass current to the point where they destroy themselves. This means that some method of limiting the current is mandatory. In the old days this would be a simple resistor but that was inefficient. Today, where achieving the most light with the least power usage, integrated circuits are used. If the IC is inside the light head then it would be possible to run the light from DC although I'd consider dropping the voltage from 13.2V (or whatever you 12V circuit sees during charging) down to closer to the 8.5V you noted. The forward drop of a string of common silicon rectifier diodes will do the job pretty well and cheaply -- each diode commonly drops about 0.7V in the forward direction. On the other had, if the IC is in the power supply then connecting the light directly to a high-current DC source will burn it out in a flash (literally).

Re: OT: Electrical DC ??

#4

Re: OT: Electrical DC ??

Dan Donaldson

>The most efficient way to do what you are asking is probably a buck/boost dc/dc converter. Do a search on google for them and you should find something that works. I found one on a quick look, but it was about $70. (it was an industrial grade one)

Especially since you are off grid, you would want to have the best efficiency that you can get. Typically these types of units are 85% or better. If you are handy, it would not be too hard to find the parts and schematics to build one.

Re: OT: Electrical DC ??

#6

You'll save time/money......

Mark Goodall - ATL - tooljunkie

>I think you'd save time/money if you simply went and bought a 12V LED lamp or LED bulb. I just bought some LED "bulbs" that fit in the existing sockets in the car at AutoZone yesterday and was surprised at how many different types of 12V LED lights you can buy now. Cigarette lighter plug lights with goose neck arms and LED lights for reading maps in cars, etc.

Just go to your local automotive store and find the 17 year old who just stepped out of his lowered Honda Civic with the glowing blue lights under the chassis and follow him to the "Bling" LED lights aisle.

Happy Woodworking!