Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Waterski, Serial #1

Posts

Waterski, Serial #1

#1

Waterski, Serial #1

Grant in Iowa

>About three years ago I had a good long look at the wooden waterskis our local show ski team uses to pull off their stunts. They looked fairly simple to build, so I mentioned that I might be able to build some for the team.

First, I studied bentwood laminations,epoxies, glues, finishes, and everything in between. Probably the longest delay in the project was stopping to build a house in there somewhere.

Pictured below is Serial #1, a prototype that was ridden upon last evening for the first time by three impressed skiers.

The ski is made of three 1/4" thick resawn layers taken from ash blanks, clamped to the form in a vacuum press. I used DAP Weldwood Plastic resin glue, at the recommendation of a 60 year veteran of waterski building.

The ski has four coats of Helmsman spar urethane finish brushed on and sanded lightly between coats.

This particular ski is wider than most recreational skis because it is designed to be a wide, stable platform for a line of girls doing "chorus girl" type movements on the water. The skiers only criticism was related to the positioning of the binding, so I did pretty well with "Old #1"!

The production versions will likely be laminated top and bottom with Formica for durability. The fins will be made of 3/4" HDPE instead of the pictured ash.

Regards,

Grant in Iowa


img

Re: Waterski, Serial #1

#2

Another picture

Grant in Iowa

>Here's a photo showing the edge and front bend of the ski. I used layers of 1.5" foam to create the form that the ski is bent on in the vacuum press. Note that the blemishes are sand, which is a badge of honor in this case.


img

Re: Waterski, Serial #1

#3

Yet Another picture

Grant in Iowa

>Here's a closeup of the rear of the ski. The wooden fins were temporary just to get it on the water for testing. They will be replaced with HDPE for durability.

Note the 3 layers of laminations and the staggered joints in the individual layers for strength. The top and bottom layers have 3 glue joints and were resawn from the same blank, while the center layer has only one joint in the center and is resawn from its own blank.

The glue lines seem thick because of the glue used. It performs best when it has a .005" glue line.

An interesting glue note is that the DAP Weldwood Plastic resin glue container says "Ideal for interior application", which is a new addition according to the veteran ski builder I have consulted. He says he has NEVER had a ski come apart at the glue lines with this product. The more I work with this glue, the more I am im"pressed". It is a two part glue with one being a powdered resin product and the other being water. You mix the two parts together for the desired consistency and have a pot life as long as one to five hours depending on temperature in the work area.


img

Re: Waterski, Serial #1

#5

Should Dave Goode be scared?

Kneale Brownson..Awaiting return to CO snows

>

Re: Waterski, Serial #1

#6

Re: Waterski, Serial #1

Bill Wilkinson

>Very nice job. Well done

My father made water skis for our family in the 60's and 70's - he used ash and resourcinol glue, and finished the outside with polyurathane.

He cut a groove down the end with a bandsaw, and bent it in a press. The resourcinol glue holds very well even in a thick layer.

Some of those skis saw much usage, and are still in very good condition. They needed refinishing about every ten years.

The dual wood fins were normal on jumper skis - they held up on the ramp very well, although they created more drag.

If you can find a way to put a tunnel down the center, it would improve the stability quite a bit.