Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Jet Supersaw fence problem

Posts

Jet Supersaw fence problem

#1

Jet Supersaw fence problem

AD

>Hi all,

I have searched through the archives but have not been able to find an answer to my problem.

I have a Jet Supersaw with the micro glide fence. This fence was ok when the saw was new but it had a habit of the locking lever popping up every now and then. This problem has gotten worse and after pushing the handle down harder and harder it snapped off ( so I replaced it with a high tensile bolt setup).

A bit of reading on the net shows that this has been an issue with this fence but I have not been able to find a fix for it yet. Jet are bloody useless and even though they are aware of the problem have no idea how to fix it except have me spend $400 plus on the Xacta fence.

Has anyone else had this problem and found a solution?

TIA

Andrew

Re: Jet Supersaw fence problem

#2

A.J. Hamler

Re: Jet Supersaw fence problem

A.J. Hamler

>Hi Andrew...

I had the same problem with mine, and with the same result -- I snapped off the handle. I also replaced the handle as you did with a high-strength bolt epoxied inside of a custom ebony handle I turned on the lathe.

When mine started slipping I flipped the fence over and completely blew out the works with my compressor hose, as well as the track on which it rides. Now, a little bit of dust shouldn't cause a fence's locking handle to slip like that, but thoroughly cleaning out the mechanism seemed to do the trick.

At least I think so. It's quite possible that the act of turning it upside down and blowing it out may have jostled the locking mechanism just right. Also, the new handle I made allows me to lock it down very securely. It's possible the improvement is a result of all three -- jostling, cleaning and new handle. In any event, I'm not having the problem now.

And yes, that fence is junk. I love Jet equipment and am otherwise very pleased with this saw, but I sure hope they've improved the fence on the SuperSaw since I got mine.

A.J.

Re: Jet Supersaw fence problem

#3

Re: Jet Supersaw fence problem

AD

>Thanks for the reply AJ.

I have tried all those but it still pops up at the worst possible moment. I was hoping there was a majic cure-all that another owner had found before I splash out on another fence. I'm a bit reluctant to buy another Jet fence but I have heard that there is some issues with fitting aftermarket fences to this saw so I might not have a choice.

regards,

Andrew

Re: Jet Supersaw fence problem

#4

Re: Jet Supersaw fence problem

Kelly Anderson

>Mine did the same thing in the middle of a rip cut, scared the heck out of me. I think that I only got it to lock once or twice after that. I got the distributor to come and look at it and was able to convince him to trade it out with an xacta for the Super Saw. It is a much better fence.

Re: Jet Supersaw fence problem

#5

Re: Jet Supersaw fence problem

Phil Joines Krum,Tx

>If Jet won't fix it then it sounds like a case for the Consumer Product Safety Communication to me.

Re: Jet Supersaw fence problem

#6

Re: Jet Supersaw fence problem

AD

>Hi Kelly,

When you say the Xacta fence is better, would you sau it is comparable to some of the other biesmeyer style fences on the market or is it a gimmick like the micro glide fence?

regards,

Andrew

Re: Jet Supersaw fence problem

#7

Re: Jet Supersaw fence problem

Kelly Anderson

>I meant that it is better than the Micro Glide fence. It locks and stays put and is easy to adjust for square etc. I have not used any of the other fences. In looking at the Biesemeyer fence at my local Sears on their saw I would say that it is comparable, similar design of course, quality materials but again I have never used a Biesemeyer fence.