Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

preparing oak for gluing up table top

Posts

preparing oak for gluing up table top

#1

preparing oak for gluing up table top

John Neel

>I am attempting my first oak trestle table, and need advice. I had my boards face joined (or is it "jointed"?) and planed where I purchased them, and I edged joined them in my shop.

The problem is that when I dry-assemble the planks for the table top the edges are not perfectly mated in all places, indicating a little twist in some of the boards. My question is how much of this mis-alignment is acceptable? And if I contrived enough clamping devices to press all the boards into perfect alignment before clamping the glued edges together, will this result in harmful stresses in the finished top that could cause warpage?

I will appreciate any advice for an old guy who is nevertheless a novice when it comes to fine furniture building.

Re: preparing oak for gluing up table top

#2

Re: preparing oak for gluing up table top

Dick Coers

>It would helpful if we knew how wide the boards are, and how much they are misaligned. I have never put a panel together that didn't need some pressure in one direction or another, to get the boards lined up. But then again, there has never been a top that didn't need a little more dressing on one joint or another after glueup.

Re: preparing oak for gluing up table top

#3

Re: preparing oak for gluing up table top

George@Colonel's Workshop-Havertown PA

>Good Afternoon John,

Getting it perfect is a matter of addressing all the imperfactions. I've done quite a few tables and never had any board behave 100% in relation to its neighbors. Dry clamp and see if the boards close over their length. I often use cawls and C-Clamps at the board ends to insure they are very close to the same plane.

When you have it glued up, use a plane/scraper/ROS to even out the adjacent board surfaces. Once they are even, commence with the sanding schedule. It will look fine, I am sure. And, oak is pretty forgiving visually, thanks to its open grain and structure.

George

Re: preparing oak for gluing up table top

#4

Re: preparing oak for gluing up table top

John Neel

>Thanks for the fast and very helpful responses to my question on gluing up boards that don't perfectly line up. It is good to know that minor mis-alignments are the rule, not the exception, and that it will not cause problems to do a little forcing into line before gluing.

Thanks very much. And I am very impressed once again with the generosity of experienced woodworkers.

Thanks,

John

Re: preparing oak for gluing up table top

#5

Re: preparing oak for gluing up table top

Kneale Brownson..Awaiting return to CO snows

>There is some thought that alternating the grain of the board when starting the glue-up will help prevent future warpage.

As George says, you almost always have to finish a dried glue-up with some scraping/sanding to make all the edges one level. That's why they produce widebelt sanders for those who face this challenge every day.

Re: preparing oak for gluing up table top

#6

Re: preparing oak for gluing up table top

Dan Donaldson

>I usually look at it such that if I can force them into alignment by hand, then it is ok and glue it up. If I have to use clamps to get it to line up, then I might think a bit more about prep. As stated, I don't think that I have ever glued up a panel that did not need at least some level of "persuasion" to get everything perfectly lined up.

Re: preparing oak for gluing up table top

#7

Jim Rahbe, Bedford Texas

Glue up Suggestion...

Jim Rahbe, Bedford Texas

>John,

Not sure if you are planning to glue up your tabletop all at once, or in segments. Assuming you are going to have to tweak the boards to get them to line up correctly, I suggest that you divide this task into smaller and more manageable segments. If your top has four boards, I�d only glue two boards together at one time. If you have enough clamps, while the first two are drying, you can then glue the remaining two boards together. Once these two glue-ups are dry, you can then glue the two sets of boards together to make the completed top.

You certainly don�t have to do it this way, but I find it is better to take an extra day to do the glue up, than to spend the next day kicking myself for not getting everything aligned correctly.

Jim R.