Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Router Plate Problem

Posts

Router Plate Problem

#1

Router Plate Problem

Al Goldstein

>Just finished building my router table. I used the MLCS aluminum router plate. The four allen screws in the router plate corners made adjusting the plate height very easy.

The problem is that when routing the vibration of the router plate causes the allen screws to rotate and the plate slowly drops.

I don't want to use Loctite to permanently set the allen screws - I don't like permanent solutions. Is there any substance that would prevent the allen screws from rotating and is reversible?

TIA

Re: Router Plate Problem

#2

Re: Router Plate Problem

Grant Wilkinson

>You could use Loctite Blue. It's not permanent.

Re: Router Plate Problem

#3

Re: Router Plate Problem

john lucas

>Al They make set screws that are locking screws. They have a nylon or some sort of plastic piece stuck in a groove. They can be adjusted but will stay in position. I need to order some to replace some screws in a couple of places where they come loose also. I had forgotten about it but I'll dig through my catalogs and find them.

Re: Router Plate Problem

#4

Re: Router Plate Problem

George@Colonel's Workshop-Havertown PA

>Good Afternoon Al,

I had that problem a few years ago and used simple shims to cure it. You may try and add some tape to the underside of your table or on the opening's flange(s).

George

Re: Router Plate Problem

#5

Re: Router Plate Problem

john lucas

>I just checked with Fastenal and they can get 2 types. One has locktite built into it and the other has a nylon insert.

Re: Router Plate Problem

#6

Re: Router Plate Problem

Rick in Colgate, Wi

>Like Grant said, blue loctite is designed for vibration applications and fasteners can be easily removed or adjusted. I've used it on all my woodworking tool assembly fasteners including my router plate.

Re: Router Plate Problem

#7

Concur on Loctite

Bill Houghton, Sebastopol, CA

>There's a post-installation version that you can put on without removing the screws (green, if I recall the color; but I haven't purchased any for some years, so maybe the color changed) - works its way down into the threads by capillary action. It's among the weakest of the formulations.

One of the neat things is that the compound stays down in the threads, at least for a while, so it will resist loosening even after you've broken the seal. There's a kind of gritty plastic feel to the fastener.

Any auto parts or hardware store should have Loctite or the Permatex version of it, so this is probably cheaper than a screw with a nylon insert after allowing for shipping, unless you're lucky enough to have a good industrial supply outlet near you.

Re: Router Plate Problem

#8

Thanks

Al Goldstein

>Thanks guys. I'll get some blue Loctite.

Re: Router Plate Problem

#9

Re: Thanks

Dan Donaldson

>Just make sure you don't accidentally get red if you ever want to adjust the screws again. ;-)

Re: Router Plate Problem

#10

Jesper, Denmark

Re: The quick, dirty and cheap version.....

Jesper, Denmark

>Use a little ordinary wood glue on the screws. It holds just enough that they do not unscrew, but can still be removed.

Re: Router Plate Problem

#11

A word about loctite

Lee Schierer - McKean, PA

>Everyone thinks the red loctite is forever. Well it isn't. Heat it up to about 250-300 degrees and it will let you loosen the screw. This is easily done with a soldering iron.

All the loctite threadlockers lose their holding power with heat.

Lee

Re: Router Plate Problem

#12

Do you fish?

Tim Greif - West of Chicago

>Try hanging a little piece of ultralight monofilament line into the hole before you thread in the setscrew. Should provide enough resistance to make it self locking and vibration proof.

Re: Router Plate Problem

#13

Now That Solution has Great A lure, Tim

George@Colonel's Workshop-Havertown PA

>

Re: Router Plate Problem

#14

You might also consider...

Dave Bair, Eaton Rapids, MI

>why your router is vibrating so badly; is it runout from bad shaft or bad bit? Either way, it can't be producing very good cuts.

Re: Router Plate Problem

#15

Re: You might also consider...

Fred Davis

>Nerves??

Save yourself a trip to the store and put a drop of Shellac on the screw.

FredD

Re: Router Plate Problem

#16

Or: the decorative solution

Bill Houghton, Sebastopol, CA

>Reaching back into the mental archives, in my motorcycling days, one of the solutions was to use some nail polish: put it on, insert setscrew fairly quickly. Color seems not to matter.

Re: Router Plate Problem

#17

Re: Or: the decorative solution

Bill White

>Bill, I always used a candy red on my stuff....BLUSH!!!!

Oh, Loctite blue.

Bill

Re: Router Plate Problem

#18

Vibrations

Al Goldstein

>Wow, these are great solutions. I'll try the blue loctite first. I do like the nylon monofilament suggestion as well.

My router, a 2 1/4 HP Triton, works well. I first tried a phenolic router plate in my router table, but I didn't like the sag. Then I replaced it with an aluminum plate that is slightly smaller and doesn't fit as well in the insert rectangle I cut for the phenolic plate. This loose fit might amplify the vibrations. I'll wedge the aluminum plate in the insert rectangle with those dummy credit cards that I always get in the mail. Should help a bit.

Thanks again for all the mental energy.

Al

Re: Router Plate Problem

#19

Time for duct tape!

Bill Houghton, Sebastopol, CA

>a thin line of duct tape around the perimeter of the plate...shock absorbing as well.

Re: Router Plate Problem

#20

Re: A word about loctite

Charlie Self

>I think that, and the fact that aircraft lock nuts don't work at all well, is why we used safety wire in the USMC helicopters I worked on back in the late '50s, early '60s.

Re: Router Plate Problem

#21

Re: Vibrations

Don Evans

>I don't think going by the color is really great idea, here is a run down of some of the more popular Locetite's by number:

Number is front of bottle:

222MS Locks and seals small screws

242 This is a removeable locktite with normal hand tools, it locks and seals nuts, bolts, screws and fittings.

262 PERMANENT locker Heavy duty use for bolts and studs

271 ADHESIVE/SEALER, locks and seals plugs, bolts and nuts.

For your problem I would go with the 242....

Don

Re: Router Plate Problem

#22

Neat DIY "Nylock" solution!!

Kneale Brownson..Awaiting return to CO snows

>

Re: Router Plate Problem

#23

242

Al Goldstein

>Don,

Thanks for the information. I looked through my glue drawer and found two knock-offs for loctite: Lock-it and Pro Lok. They both indicate they prevent screws from loosening from vibrations and they can be removed with normal hand tools. So they seem to be equivalent to 242. I'll pick the one that hasn't dried out.

Boy, I learned a lot with this simple post. And that is the real benefit of being a member of Woodcentral. Thanks Ellis.

Al

Re: Router Plate Problem

#24

A quick drop of hot melt glue.

Alan in Little Washington (NC)

>