Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Workbench tiop question

Posts

Workbench tiop question

#1

Steven Antonucci

Workbench tiop question

steve antonucci

>I have a bunch of QSWO that has been taking up space for a long time in my shop. Most of it is less than 5' in length. I'm thinking I want to use it to make a 6' long bench top, hence my question:

is there any major design problem with milling the top and laying it out the way you'd build a floor? I'm thinking that I'd like it to be 3" thick, and most of the top would have tow or three 3/4" boards running the length in short sections vs the whole 6'.

It's more work, but I have the wood on hand and I want to get it "out of the way" to reclaim the floor space.

Thanks

Steve

Re: Workbench tiop question

#2

JL

Re: Workbench top question

JL

>If you were anywhere close, I would drive over and help you with your problem! I'd bring you some wood to trade.

My personal preferences are not to use larger pored wood for workbench tops. That being said, what you propose to do should work very well and is done all of the time. Just make sure that you stagger the joints enough. Do you have a finger joint bit for your router? That would help also.

Re: Workbench tiop question

#3

DITTO

George@Colonel's Workshop-Havertown PA

>

Re: Workbench tiop question

#4

Re: Workbench top question

Jack Prescott

>My work bench top is made from "truck flooring" which is used in the floors of 18 wheelers. The truck flooring is made by gluing one inch wide by about one inch thick pieces of hardwood together. The top is layed on three layers of 3/4 inch MDF which is glued and screwed together = stable and tough to say the least.

I leveled the top once assembled with a router mounted on a frame. I then finished the top by sanding, applying 2 coats of tung oil smoothed with steel wool between coats, and then applying Johnson's paste wax 3 times. This finishing method recommended to me by Howard Acheson is outstanding = it is an "in wood" finish using the tung oil.

The top is tough as nails and nothing sticks to it our penetrates it = paint just peels off with no effort due to the wax. I reapply the wax about every 6 months or so after a steel wool treatment.

This is probably more info than you wanted, but the short answer is "go for it"!!!!

Re: Workbench tiop question

#5

Re: Workbench tiop question

R Payne

>Sounds like you are proposing to do what I did last year and so far so good.

ron

Re: Workbench tiop question

#6

Re: Workbench tiop question

Rick Garner

>What you have in mind will work but will be time consuming...plus, I hate to see all that QSWO get buried in a work bench. Have you considered selling the QSWO and use the funds to buy another material for the top? I've always thought a piece of 3-1/4" x 15" x 12' (in your case) glulam would make an exceptional bench top. Just cut in half and join once to get a +/- 30" wide surface, then flatten using your method of choice, and voila!!!

Re: Workbench tiop question

#7

Re: Workbench tiop question

Fred Davis

>Rick,

I did a glu-lam bench top about twenty five years ago , and put it on a pedastal base with a drawer box .

Stil have it , it is hell for strong , but I found the Doug Fir to be softer then I like for a bench.

Glu-Lams make a great fast to make bench for outside also.

FredD

Re: Workbench tiop question

#8

Steven Antonucci

It was either QSWO or quilted cherry

steve antonucci

>I know it will be a lot more work than buying lumber fresh, but it is on hand which makes it the likely winner. It's a lot of shorts and all needs to be surfaced, but I expect that I'll consume a fair amount of the pile in doing so, which is the end goal.

Unless someone in NJ wants to make a deal on a truckload of short, highly figured QSWO. Boxmakers- lifetime supply!

Steve