Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Attaching Flag Cases to a Carving Vise *LINK*

Posts

Attaching Flag Cases to a Carving Vise *LINK*

#1

Attaching Flag Cases to a Carving Vise *LINK*

DaleLenz

>Thinking about building a carving vise as shown in the link below. I'll be using the "vise" to attach my flag cases to while I sand and especially when I use the elect. buffer to buff out the finish, should make life easier(?). Trying to wrap my head around how I'd attach the flag case to the vise. Since the flag case will be near finished when attaching, I believe it needs to be fastened somehow to the inside of the case. One thing for sure, don't want the case coming loose! My shop might get a new window from me chunkin the vise through the wall, : ' >.


Carving Vise

Re: Attaching Flag Cases to a Carving Vise *LINK*

#2

JL

Re: Attaching Flag Cases to a Carving Vise

JL

>If money were no object, I'd get a pattern maker's vise. Trouble is, they cost a bit ($260).

I like his ideas though. I don't know if double sided carpet tape would work with buffing. I have used it to hold down wood while jointing and planing.

Re: Attaching Flag Cases to a Carving Vise *LINK*

#3

Re:Thanks, JL for the post

DaleLenz

>I've looked at pattern maker's vises, Tucker and others. My main interest initial was holding the flag case while I buff. Need to gently clamp the case down to do the sides on a pad laying on the bench. Then lay the case, facing up, on the bench unclamped while I buff the flag case's face, case wants to go sliding off the bench. Have used padded clamps while face buffing, but it still leaves a superficial marks on the finish.

Re: Attaching Flag Cases to a Carving Vise *LINK*

#4

Re:Thanks, JL for the post

Glenn Madsen near San Francisco

>Have you looked at vacuum clamping? The fellow across the street uses it for his ShopBot CNC. The parts look pretty simple.

You're still into it for a couple hundred dollars...

Re: Attaching Flag Cases to a Carving Vise *LINK*

#5

Re: Attaching Flag Cases to a Carving Vise

Tony - Memphis

>I remember that vise. I have the magazine that it was in at home. I was wondering if you could make a plate that would fit inside your case that expands. Hard to explain in words, but imagine the triangle shaped plate that is attached to the vise via screws. One edge of the vise maybe moves on pins and has a threaded rod that you turn with an open end wrench to snug it against the inside face of the case. You could also maybe get way with making it tapered and sort of wedging the case onto the plate? I'm just thinking out loud here, sorry if it just sounds like babble. One more idea...they make those quick grip type clamps now that work backwards. You might could figure out a way to use one of those to hold the case and the clamp is attached firmly to the vise.

Let us know what you figure out. We will all run into something similar someday.

Tony

Re: Attaching Flag Cases to a Carving Vise *LINK*

#6

Re: Good ideas so far...

DaleLenz

>Glenn: haven't considered vacuum clamps on this idea, will check it out. Not wild about 200 bucks but once I get into vacuum clamping, it could turn my world in a neat direction.

Tony: My current thoughts are similar to yours; considered the cam thingys, have a few, but I'm thinking since my face frame is only 5/16" thick, I'd run the chance of opening up the miters.

Re: Attaching Flag Cases to a Carving Vise *LINK*

#7

JL

What about the new Rockler "puck pads"??

JL

>Or whatever they call them.

I've also used a waffle weave. sort of open shelf liner to stablize table tops on my bench when I rout the edges. I lay out a piece of the liner on the bench top and then put the table top on the liner. I have to toss or trim the liner when I get too much dust on it, but it works pretty good for table tops. I figure a flag case will have an area of about 240 sq. inches on the back and maybe 88 sq. inches on the side. That should give you a bit to grip on/to.

Re: Attaching Flag Cases to a Carving Vise *LINK*

#8

Another thought: Tooling holes

Eddie Pacheco: Antioch, Ca.

>Dale,

The flag cases are your design. Any chance you can come up with a place along the inside where you could drill a blind hole or slot in each piece, during construction, and then come up with a simple scheme to secure your assembled flag cases via these holes or slots? Maybe like a plywood fab'ed scroll chuck that you engage the holes or slots, expand the chuck and lock it down. Then this assembly can be secured to your bench for sanding, applying finish, and buffing. I think there's a scroll chuck article in the turning archives.

Re: Attaching Flag Cases to a Carving Vise *LINK*

#9

Re: Been thinking about this...

DaleLenz

>for several days now. What I've came up with as Tony suggested; make a 3/4" plywood plate slightly smaller than the back opening of the flag case, attach plywood plate to vise with screws or bolts and nuts. Then using pocket screws, one/side run the screws into the inside sides. More invasive than I wanted but shouldn't be a problem. After I remove the plywood plate, hit the screw holes with 150 sandpaper; lay some shellac inside the case and call it good, at least in theory.

Like Tony's other idea of a vacuum clamp, may do that in the future. Good idea, Eddie, with the outspreading jaws. Screw to the plywood plate sounds like less work. Gotta watch out for over time; the "screw-pockets" could get compressed in the plywood, to where the screw could go through the flag case's side, hugh bummer!

I thank everyone for their thoughts. If someone else has thoughts, please toss them in.

Dale

Re: Attaching Flag Cases to a Carving Vise *LINK*

#10

What about Tony's idea w/cam levers

Eddie Pacheco; Antioch, Ca.

>Instead of pocket screws. How about 3 cam levers that grab the inside of the case? You could put a rubber O-ring along the whole profile and that would provide more friction to secure the frames. Just a thought.

Re: Attaching Flag Cases to a Carving Vise *LINK*

#11

Re: ?

DaleLenz

>Sorry Eddie,

I can not follow your idea. Care to draw me a picture, : ' >.

Re: Attaching Flag Cases to a Carving Vise *LINK*

#12

Picture sent

Eddie Pacheco; Antioch, Ca.

>

Re: Attaching Flag Cases to a Carving Vise *LINK*

#13

Re: Gottcha, Eddie *LINK*

DaleLenz

>Sorry, took me awhile to "see the picture", :'>. If I indeed understand you suggest; put force on the inside of the case with those cam thingys(?), correct. I'm not real crazy about doing that as I'm afraid I could pop one of the three face frame miters, they are only 5/16" in thickness x 1/2" in length.

Another thought: Use 3/4" plywood for mass, rabbet to fit inside rabbet in flag case's back, see link. Use brass buttons, that are going to be installed anyway, attach plywood to vise. Don't have to screw any holes into the inside of flag case. Everything depends on how well the 3/4" plywood panel fits, might work. : ' >. What y'all think?


Flag Case's Back Panel

Re: Attaching Flag Cases to a Carving Vise *LINK*

#14

Re: A Big Thanks! Eddie

DaleLenz

>

Re: Attaching Flag Cases to a Carving Vise *LINK*

#15

Yeah, your idea mo' better, Dale.

Eddie Pacheco; Antioch, Ca.

>