Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Best way to trim Cabinet Face frames *LINK*

Posts

Best way to trim Cabinet Face frames *LINK*

#1

Best way to trim Cabinet Face frames *LINK*

Bernard

>After months of working on my bookshelf project in my spare time, I am virtually done. Several months ago, I had purchased the oak doors and stained and finished them, and put them safely in the guest bedroom to avoid any damage to them. I am ready to go install this project at my daughter's house this week, and started to install the doors last night. Oh no!

After installing a few sets of doors (2 doors per opening, no mullion), they actually overlap a bit, even after setting the width adjustment screw at max (it is a 3-way face frame hinge, virtually identical to the one in the link).

After the initial panic set in, I realized that my only solution (I think) is to shave the face frame where the hinge is attached, to effectively widen the openings. Probably 1/16" or 1/8" on each opening (a 6-foot wide cabinet with 3 openings, and then 2 of 27" cabinets), maybe one side only , maybe both.

My question is this: what would be the best way to do this to do this EFFECTIVELY and SAFELY? My thought was to set the cabinets back on their backs and then build a little jig guide, and then router it out. Or is there an easier way? I am open to any and all suggestions, although I will probably have to do it tonight, since I already have the 16 foot truck reserved for Wednesday to bring it to her house (it is in 6 sections...all in Oak plywood and Oak boards).

And yes, I know that I have to post pics after it is done, or else I really did not do it.

I appreciate all of your comments, and welcome them all. Thank you in advance.


Hinge type

Re: Best way to trim Cabinet Face frames *LINK*

#2

Re: Best way to trim Cabinet Face frames

Fred Davis

>If your doors close together without a mullion or stile between them , shave the door edges that meet with a sharp plane or a jointer it you have one , restain the edge and your good to go.

Shaving the hinge side of the face frame while not impossibile , is a lot more work and easy to ruin a frame if the router or the straight edge slips.

One of the advantages of making your own doors is that these type errors are caught early.

FredD

Re: Best way to trim Cabinet Face frames *LINK*

#3

Re: Best way to trim Cabinet Face frames

jerryburns

>I had the same type of problm this week with a wine cabinet that i build as a wedding gift. I trimmed the door with a block plane and just touched up the stain job (I need spell check! )

Re: Best way to trim Cabinet Face frames *LINK*

#4

FINISHED Re: Best way to trim Cabinet Face frames

Bernard

>No doubt about it, trimming the doors would have been the safest route. Problem was with 10 doors, I thought it would have been a longer job. So, after marking carefully, I put in a trim bit on my router with a collet, clamped a board to guide my router, and routered out a 1/8" off of one side of each opening where the hinges go. I put some stain, inserted the doors, and it is perfect now. I just need to put some finish on the side of the face frame where the trimming was done. Since it is on the inside behind the door (the doors overlap the opening), and since there is very little routered outside of where the hinge attaches, you do not see it from the outside at all. And to be honest, you don't really notice it when you open the door either, unless you are looking for it.

Obviously, since this is going into somebody else's house (my daughter's), IF somebody notices something, the answer will be that it is a "designed inset for added stability and flexibility". Hate to call it a mistake!

Thanks again for the input, because it really made me go the extra step to be 100% that I did not take any undue chances.