Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

Posts

Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

#1

Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

Pete Austin

>Ok, I am upgrading a really really awful table saw. I've been keeping my eyes out for a good saw. I found a Grizzly 1023 that I can buy for $375, but it isn't in pristine shape. The top is a bit rusted, and the fence is crap. However, I am pretty handy - the rust is easily removed, and a fence is easily purchased. I do have 220 to my shop.

I have not seen the saw in-person yet. I have only had one call with the current owner.

I am really looking for some fast help here. I need to make a decision tomorrow (Wednesday) in order to not lose it.

I have been doing some research and the Grizzly 1023 seems to be a great great saw. However, I cannot tell from the pictures if this is a 1023S, 1023, 1023Z or what.

- What is your opinion

- What should I ask the owner?

- What should I look for when I look at it in person?

- what kind of saw is this?

I am including one picture below. I am also including a link to other pictures.

THANK YOU in advance!

Pete


img

Click here for More pictures of the saw

Re: Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

#2

Scoop it!

Forrest Addy

>Scoop it. The Griz 1023 is a great saw except for a few mettalury issue. If yours is a home shop you will never wear it out. If you're a commercial cabinet maker it might not be such a good choice in a production setting. OTH it will be a good addition as a peripheral saw cutting small parts and misc onesey twosey jobs.

As you say the price is right and rust will come off. You'll find a better fense and the miter gage kinda sucks. OTH if you tune them up they will do until your lust for new gadgets becomes overwhelming.

Re: Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

#3

Re: Help Fast!--Should I buy this table saw? Griz

GalenV in Iowa

>Surface rust is going to be a bigger job than you think and the miter gauge slots may get sloppy when you get done.

Yah chemical treatment, power sand and even pit filler can get the top back into some kind of shape but time and money.

Wonder how flat the iron is as it could be warped. Better check.

Does it run and with the lack of care will be bearings go out in a short time from setting idle and moisture getting to them.

Will the arbor, angle and depth mechanisms be rusted up too? More work!

Wonder how much rust is at base of cabinent inside and out? Full of wet sawdust?

Yes miter gauge is poor but fence may clean up, but you would have to see/feel to tell.

For condition and unknowns I think the price is too high.

Maybe $275 but $375 seems high to me with known work and unknowns.

Re: Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

#4

Looks to me like it's been sitting outside

Dan Mitchell

>I agree out the miter slots & potential bearing /motor damage, plus the fence. May be more trouble than it's worth.

Re: Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

#5

I disagree. Function first cosmetics second

Forrest Addy

>I disagree. Function first cosmetics second. Remove only the rust that interferes with the function of the saw and use a stone to do it. If you sand or (gasp!!) power sand you will finish with a crooked but shiney table. This is a table saw not fine furniture. A little staining and tarnish has no effect on the funcion, productivity, precision, and operability of the saw.

Naturally you don;t want surface rust to rub off on your work so remove it. Leave the pits in the underlying metal stay. They cause no harm. Fill them with wax. The ting to do with rust in machinery is to remove it in a way that leaves the parent metal undisturbed.

Table slots and other features have to run smoothly but don't wear away the very fits and finishes that ensures snug free moving assembly and part movement.

You might want to removee the table and see if the cradle mechanism is up to snuff. If should be because Grizzly greases hell out of them but you probably should check anyway. You will have to realign the saw table to the blase after you pit it back on but that's a small detail.

Re: Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

#6

Remove rust with a stone? How

Pete Austin

>First, thank you all for the responses. I really appreciate the quick turn-around. I will be heading over today, if I can. You mentioned removing rust with a stone. I've never heard of such a thing - can you provide a bit more info?

And, any other suggestions would be greatly appreciated.

Re: Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

#7

Re: Help Fast!--Should I buy this table saw? Griz

Doug Ridley

>IF it runs and you want to tackle it as a project, make an offer of 300 or even 275. It never hurts to try. The worst he can do is to say no.

Re: Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

#8

Not At That Price

Dave's Not Here

>

Re: Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

#9

First rust will really load a stone

Forrest Addy

>First rust will really load a stone - clog it right up. Use a coarrse bench stone is pretty good condition. Pout on a little mineral spirits paint remover to make a puddle. Stone very gently pausing to wipe off slurry and reapply thinner. Sooner or later you will get to metal. Don't stone the metal yet keep working the rust. The may be a black film of scale under the rust. Keep the stone as clean as possible. Use a vegetable fiber brish to clean the face it need be.

I use a slightly worn coarse diamond stone with much more vigor as it does not clog as readily.

When the red rust and black scale are removed and bright metal appears continue a bit until you're satisfied but don't get carried away. Hand buff the surface with a non-woven abrasive pad (scotch brite)

Re: Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

#10

What I would do

Lee Schierer - McKean, PA

>I would flood the surface with mineral spirits or mineral oil and put a scotch brite pad on a vibratory sander instead of sand paper (wear old clothes as this method gets a bit messy). Polish the surface uniformly wih the "sander" wiping off the rust sludge and reapplying the lubricant periodically. Scotch brite is not likely to remove enough material from the surface to affect the accuracy or flatness of the surface. You could always polish the surface once the rust is gone with various levels of sand paper on a thick glass plate similar to the method used to flatten and polish plane soles (only you would move the glass plate) if you want it flatter.

Lee

Re: Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

#11

Re: Help Fast!--Should I buy this table saw? Griz

Robby Wright in San Marcos, CA

>That looks like light rust to me, the kind you get from a cast iron surface sitting without a cover indoors. If it is, get a scrap of plywood, some 600 grit sandpaper and some WD-40. Spray the surface and, using the plywood as a sanding block, lightly sand enough to get the surface rust off. Leave the pits - they won't hurt anything. Dry and wax the surface thoroughly.

Motor bearings are easy and cheap to replace. They cost about $10 apiece at the local bearing shop and can be removed and replaced by hand if you are careful. I have done many a motor in less than an hour. An arbor press helps, but isn't essential. Use a socket the size of the outer ring of the bearing to gently drive the bearing home in it seat if it needs encouragement. Never hit the center of the bearing - you will nick the ball bearings inside and bearing will fail quickly.

As long as the basic condition of the saw is in good condition, I would grap it. Add a fence, side and outfeed tables and you should have a good saw.

Robby Wright

San Marcos, CA

Re: Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

#12

$ 150.00 !

steve mackay

>

Re: Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

#13

Re: Hope it's not 3 phase.

Chuck in ND

>

Re: Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

#14

Re: First rust will really load a stone

Pete

>By "stone" do you mean a knife sharpening stone? Thanks,Pete

Re: Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

#15

Re: Help Fast!--Should I buy this table saw? Griz

Hal Smith

>Seven years ago I bought(stole for $300) a well used (by a woodworkers club) Enlon which was the predecessor of the Griz 1023 line. I've been nothing but happy with it. Solid (passes the nickel on edge test), have never stalled it, and I'm sure it will last me the rest of my woodworking days. Fortunately the top was in good shape with no rust and it had a Bies fence with some scapes where it had been set too close to the blade, but still serviceable. I'm no expert on removing rust, but surely you can make it serviceable. Put a WWII blade in mine. I'd buy it in a heartbeat. Good luck. Hal

Re: Help Fast!--Should I buy this table saw? Griz 1023 *LINK*

#16

Re: Help Fast!--Should I buy this table saw? Griz

Marv

>Hi Pete,

Always offer less than the asking price. Most sellers will price their stuff on the high side, expecting a potential buyer to negotiate the price down.

I'd offer $275 and expect to pay somewhere in between.

As for the rust, the best sandpaper I've found for rust is the black 3M brand. I buy it at Wal*Mart. For sure use a sanding block and start with about a 320 grit and use mineral spirits. You could even start with 220 and finish with 400 grit. The surface was probably never perfectly smooth anyway. No doubt had machining marks from the beginning. It's more important to have a flat surface versus a super shiney surface. The main thing is to remove all the stuff that could rub off on your wood. After sanding give it a good rub down with paste wax.

I would replace that old beat up fence with an original new one.

Good luck and make it a fun project.

Marv