Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Gorilla Glue

Posts

Gorilla Glue

#1

Gorilla Glue

Andy Lincoln,in Dearborn MI

>Not having much experience with polyuerathane glues I figured I would get the wisdom of those here.Gorilla Glue claims to be an idea glue for exterior applications.how well does it hold up over time?How does it compare to west system epoxy?I am still planning to build some outdoor furniture using white oak and the majority of construction will be M&T and lamination of the bow arms/back slats from thinner resawn stock.

Thanks,

Andy

Re: Gorilla Glue

#2

Re: Gorilla Glue

Tom Hintz

>I have a few outdoor projects built with Gorilla Glue that remain solid after 5 or 6 years outside. I also use it for extoic woods, especially things like dovetails because what foams out of the joint can be easily scraped off and then normal sanding removes it entirely without leaving a "shadow" when finish is applied.

Of course, others hate it so you will probably have to try it for yourself to see which side you land on.

Re: Gorilla Glue

#3

Re: Gorilla Glue

Chuck Kettler Greenwood IN

>I built a mahogany bench ten years ago for my sister. It has been outside since it was built. I used GG for the M&T joints and it is still holding together very well.

Re: Gorilla Glue

#4

Dumped It

Mark Mandell - Gone Round In Jersey

>After using a lot of it.

Reason? Joint failure. It [like poly finishes] doesn't penetrate the wood fibers so the bond is purely a matter of surface adhesion. If your joints have any gaps (its not sold as "gap-filling") the glue in those areas will be weaker and prone to fail, especially with movement across the joint plane.

I had several panel glue ups in ash that partially failed because (I think) I didn't have the join surfaces matched perfectly along the entire length and width of the glue surfaces. The joints "unzipped" after about a year. I also used it on some dovetail joints in a cherry couch that got used and the glue failed after less than a year; reglued with T-B III and has stayed solid for 6 years.

Issue,I think, is that the set glue in the joint is very brittle with little or no "give" so it's more likely to crack free of the wood surface.

As always, YMMV

Re: Gorilla Glue

#5

Re: Gorilla Glue

Lee Schierer - McKean, PA

>If you decide to use Gorilla glue ignore the suggestion to dampen the wood. That only causes more foaming. Wood and the air have enough moisture in them to cure the glue. As a test, place a drop of glue on a piece of glass or metal. Within a few minutes the glue will begin to foam.

Lee

Re: Gorilla Glue

#6

Good Point

Mark Mandell - Gone Round In Jersey

>The more foaming that takes place, the weaker the joint.

Re: Gorilla Glue

#7

Re: Gorilla Glue

Robby Wright in San Marcos, CA

>There was a recent article in I think FWW magazine, where they rated the glues. Urethane glue didn't fair too well. I was surprised that it didn't do well in the weathering part of the test either. Titebond III out performed it in every respect, and, since it doesn't make a mess like urethane does, it would be my first choice.

Robby Wright

San Marcos, CA

Re: Gorilla Glue

#8

TiteBond 3

Dave Bair, Eaton Rapids, MI

>It is extremely water proof, strong and applies just like you're used to.

Re: Gorilla Glue

#9

Paul Kramer

Does it creep?

Paul Kramer

>Andy mentioned using it for laminations too. How is TB 3 W/R/T 'creep?'

Re: Gorilla Glue

#10

Ellis Walentine

Pretty creepy

Ellis Walentine

>

Re: Gorilla Glue

#11

Re: Gorilla Glue

Tony - Memphis

>Nothing formal here, but I have had much better luck with epoxy than poly glue outside. I've had several panels come apart at the glue joint that were glued with poly (I used the Franklin I think). I've never had anything fail with epoxy. I just finished a garden bench in teak and I went with epoxy on it. A little messy to have to mix and I wear gloves, but it does work very well.

Tony

Re: Gorilla Glue

#12

Thanks all for the info ...

Andy Lincoln,in Dearborn,MI

>it was part of an ongoing thought to build outdoor furniture but as of an hour ago I finished assembling a patio set from HD that we purchased this morning.It was on sale/clearance to make room for the winter stuff(uggghhh) coming in.At 50% of it's original retail I bought it and extinguished the dream(for now) to build my own patio furniture.Now I can save my white oak for another day.But as I assembled this set I did mentally plan which pieces of the resin weave could eventually be replaced (if needed) by bent laminations of cedar to extend it's lifespan.It has alos been agreed that it will reside in the basement during the harsh winter months.

Thanks,

Andy


img

Re: Gorilla Glue

#13

Add

Mark Mandell - Gone Round In Jersey

>a keg cooler and 60" wide screen and the basement [aka Man Cave) is F-I-N-I-S-H-E-D.

Then go make the outdoor stuff.

(using epoxy)

Re: Gorilla Glue

#14

Re: Add

Andy Lincoln,in Dearborn,MI

>Mark,

I already have a 61" TV down there and a full stocked/refrigerated bar.I think it has been heading towards man cave status since its inception!!!Just don't tell the wife that it was planned all along.

Andy

Re: Gorilla Glue

#15

Um, "Mum's" The Word.

Mark Mandell - Gone Round In Jersey

>I love it when a plan comes together!!!

[Those ARE recliners, right?]

Re: Gorilla Glue

#16

Nice Ellis... but seriously, does it creep?

Victor Parisian

>

Re: Gorilla Glue

#17

Ellis Walentine

I'd count on it

Ellis Walentine

>I've never heard of a PVA glue that didn't creep. I can't say from personal experience that it does, because I haven't laminated anything with Titebond III. I purposely avoid using PVA for laminations.

Ellis

Re: Gorilla Glue

#18

Re: Does it creep?

Dave Bair, Eaton Rapids, MI

>Yes, it does. I failed to read the whole message and thought he was going with M&T only. For outdoor laminations, one could try Dap's plastic resin glue; at least according to it's lable, it's waterproof.