Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Spraying advice

Posts

Spraying advice

#1

Spraying advice

GolfSteve in Calgary

>I could use a bit of advice. This shouldn't be so complicated but I've paralyzed myself into doing nothing.

This cabinet is only dry assembled, so I can still choose to assemble it however I please. I want to spray water based lacquer as the finish. I've done a bit of spraying but I am far, far, far away from being good at it.


My question is: how would you assemble this to make spraying as easy as possible? I don't think I have the skill to assemble the whole thing and manage to do a good job spraying the inside of the cabinet.

I was thinking of doing the following

1. Glue up the sides then spray the sides

2. Glue up the back then spray the back

3. Spray all the other bits then glue everything up

My other option is to spray each piece individually, but this would involve a major masking tape job to keep finish out of the mortise and off the tenons.

Any better ideas out there?

Re: Spraying advice

#2

Re: Spraying advice

Kneale Brownson..Awaiting return to CO snows

>Unless you're going to install glass doors and light the interior, I'd not worry about how beautiful the sprayjob is there. In other words, I'd assemble and spray. Maybe you'll find it isn't all that bad anyway.

Re: Spraying advice

#3

Re: Spraying advice

Bill Tindall, E.TN

>I don't spray lacquer on the insides of things. I apply shellac.

Re: Spraying advice

#4

Re: Spraying advice

Clint Searl, at the base of Haycock Mtn

>I would brush the inside with a couple coats of a good waterborne poly, like Varathane, rotating the box to keet the wet surface horizontal.

Clint

Re: Spraying advice

#5

Re: Spraying advice

Marv

>If you spray your lacquer with very thin coats and apply several coats, you could do the inside complete, then do the outside. Do the outside the same, using thin coats to prevent sags and runs. Steelwool between coats.

Marv

Re: Spraying advice

#6

ERROR - DANGER

Mark Mandell - Gone Round In Jersey

>Do NOT use steel wool with waterborne finishes!! It will embed in the grain and you'll have rust spots everywhere plus fisheyes from the oil.

Synthetic wool (Scotchbrite) is fine, but vacuum (not tac) off well before recoating.

Re: Spraying advice

#7

Re: Spraying advice

Mark Mandell - Gone Round In Jersey

>I'd glue it up, the apply inside with either brush or pad.

Spray outside with working surface horizontal unless you have a "good" gun.

Re: Spraying advice

#8

Re: Spraying advice

Barry Irby

>Are those solid wood panels? If so, they tend to expand and contract.

I might be tempted to spray the panels at least a coat or two and then assemble and spray the cabinet. When I sued to do kitchen cabinets at the very least we wiped stain and finish around the edges of all the panels to make sure they had finish on the edges in case they floated or shank and revealed the edges.

Other than that, I like the shellac on the interior. Shellac does not retain much if any odor and stink up the interior. I have no experience with water based finish, but I would follow the advice and stay away from steel wool.

Re: Spraying advice

#9

shrinkage

GolfSteve in Calgary

>The panels are baltic birch plywood veneered with cherry veneers. They will be fully glued into their grooves.

Shellac on the interior is a concensus and is no problem.

Sounds like most people would spray the piece once it was fully assembled. I don't know if I have the guts to try this or not.

Re: Spraying advice

#10

Re: ERROR - DANGER

Marv

>Mark is right, I wasn't thinking water base.

Marv

Re: Spraying advice

#11

Baltic Birch?? Never Mind.

Barry Irby

>I'd spray it side by side, with that side up. At least until I got a feel for the finish.

Re: Spraying advice

#12

Re: Spraying advice

John Parker

>I spray only waterbourne products. My experience on inside of boxes is, waterbourne products do not fog very well. Inside of a box it is very hard to get to the inside corners. With solvent based products you have a longer flash time on the solvent, this allows you to fog in the corners. The water based dries too fast to allow you time to do this. I would spay as much of the inside as I could before assembly. I have sprayed carcasses after but the inside finish is never smooth or uniform. Your spray equipment will also determine how you finish. Good luck.

John

Re: Spraying advice

#13

Guts

Mark Mandell - Gone Round In Jersey

>Detail you spray rig, Steve, and what material are you using?

Re: Spraying advice

#14

Ellis Walentine

Spraying waterborne finish

Ellis Walentine

>John, thanks for your insights. Do you recommend any particular gun or compressor setup for spraying waterbornes? And, if you don't mind my asking, do you prefer one product line over another?

Ellis Walentine, Host

Re: Spraying advice

#15

Re: Spraying waterborne finish

John Parker

>I use HVLP conversion guns. I have a Asturo gravity gun and a Walcom Geo. The products I use are from Target. My compressor is a 5 horse Cambell Hausfeld. I am not a production shop but I use my system on a regular basis.I sprayed industrial equipment for a year a long time ago with standard siphon fed binks spray guns.

Thanks for asking, John

Re: Spraying advice

#16

equipment

GolfSteve in Calgary

>I have a Sata Minijet IV HVLP gun with a large compressor. I'll be spraying alcohol based dewaxed shellac and then the Target water based lacquer.

Re: Spraying advice

#17

Re: Spraying advice

GolfSteve in Calgary

>Hi John,

Part of the reason I'm so worried is that I recently sprayed a dollhouse with alcohol based shellac. The outside was fine, but I was not able to get into the inside corners the way I would like and the inside finish was not very good.

The dollhouse rooms I was spraying into were very small (say 6"x8"x8") so you couldn't get the gun in there and I ended up using a narrow, but forceful, jet to attempt to get the finish into the back corners. The material seemed to dry out before getting to the corners and not much of it actually stuck.

Re: Spraying advice

#18

Nice Gun +

Mark Mandell - Gone Round In Jersey

>Watch your gun pressure or you'll defeat the HVLP quality; 25-30psi is about max. Using a gun-mounted mini regulator will give you much more precise control.

Your shellac: If you mix from flakes, make a fresh batch for your piece and before you use it, run it through a paper coffee filter. If you're using SealCoat, make sure it's not more than 6 month's old from the "born-on" date on the can. Here's why: From contact with Jeff Weiss, the owner of Target Coatings, I learned (the hard way) that they, and other waterborne manufacturers, have been having problems with cold checking (coating fractures) of a shellac layer under their waterborne coatings. Much of the problem may be esterification in the shellac because of age that is further compounded by too heavy a shellac application.

The remedy is first to use only the freshest dewaxed shellac for your sealing coat under the waterborne. If you (as do I) use darker shades of shellac to tone and blend parts of the workpiece, consider using some Transtint dye in the shellac and using less shellac. Two light shellac coats should be enough to give you some grain "pop" and prevent the waterborne from raising the grain. BTW, DO NOT use a "wetting agent" in your shellac as you'll get fisheyes a/o adhesion problems in waterborne topcoats.

Next, be sure to let your shellac dry very well before applying the waterborne. I wait at least 24 hours, longer in humid conditions. You need to let the alcohol fully migrate and evaporate out of the shellac layer or it messes with the topcoat chemistry.

Topcoat: Since you're using a minigun with a lower application rate, consider using some Target SA-5 retarder in your Target finish, and keep your gun moving close to the surface (6-9 inches). It gives the coating a bit more time to flow out and level, and gives better penetration of spray mist into corners and details. In my view, it's pretty much required when spraying with RH levels below 50% as waterbornes dry so quickly that orange peel gets to be a real issue. The SA-5 will help, but you'll have to be more careful about runs and sags on vertical surfaces.

Hope this helps. Remember to practice on some scrap.

mm

Re: Spraying advice

#19

Re: Spraying advice

Fred Davis

>All of the problems associated with water borne lacquer over Shellac or anything else for that matter disappear with the use of solvent lacquer sanding sealer and naturally, Solvent based Lacquer.

No grain raising to deal with, no adhesion problems, better look and depth, burn in to each previous coat for a chemical bond and if your article is to small for a gun , finish the inside first.

Shellac is a beautiful finish in it's own right , but it's a gummy bear to sand prior to a finish coat.

FredD