Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Preferred cutting board woods?

Posts

Preferred cutting board woods?

#1

JL

Preferred cutting board woods?

JL

>Was that informative enough, Bill? ;).

I don't want to glue-up boards, I just want plain sawn boards.

I typically prefer maple (hard as opposed to soft) and cherry.

I would prefer not to use oak, ash, hackberry, etc. due to the pores. That sort of also leaves out black walnut also.

So, which other woods do ya'll prefer or suggest?

Re: Preferred cutting board woods?

#2

Birch

Ken Oakley-Sunny St. Cloud, Fla.

>

Re: Preferred cutting board woods?

#3

American Beech

Mark Mandell - Gone Round In Jersey

>

Re: Preferred cutting board woods?

#4

Re: Preferred cutting board woods?

David Yoho

>JL, you lost me when you said - I don't want to glue-up boards, I just want plain sawn boards. Are you saying you won't be cutting strips and gluing them together?

I like maple; soft is fine and certainly hard enough with the added bonus when there is some curly figure. I think cherry, beech, and birch come to mind as well.

David

Re: Preferred cutting board woods?

#5

Re: Preferred cutting board woods? w/link

paul in AZ------WebKitFormBoundary+isMX5X2paiDYC5e

>If not wanting to glue up wood means flat one piece boards your choices may be limited by availability of whatever kind of lumber wide enough to make a board. Do you mean that you don't want to glue up various strips to make the width; or cut these to make end grain butcher block?

The latter is not all that hard to do. I've used maple [both hard and soft]; cherry; walnut; wenge; jatoba and olive wood. Once sealed with several coats of mineral oil none have been a problem. I have avoided the open pored woods as you mention.

A useful site: http://www.toolcrib.com/blog/2008/10/14/20-free-cutting-board-plans-the-4-that-blew-my-mind/

Re: Preferred cutting board woods?

#6

Re: Preferred cuttin,oard woods?

Howard Acheson

>The preferred, and most often used, woods for cutting boards are maple, birch and beech. Contrasting woods are cherry and walnut although walnut is starting to get a little soft for cutting boards.

Re: Preferred cutting board woods?

#7

JL

Right, I don't want to glue.

JL

>I've got some 10"+ yellow birch. I have some 10"+ soft maple.

I was wondering what other species were preferred.

Re: Preferred cutting board woods?

#8

Ellis Walentine

Cutting board woods

Ellis Walentine

>I've made and used cutting boards of all kinds of wood and construction. Believe it or not, the one that I use the most -- because of its size and shape, not its species -- is a one-piece board of mahogany. One thing to consider with one-piece boards is that the wood should be a fairly stable species, or it should be quartersawn. Cutting boards often are wetter on one side than another, and flat-sawn species with larger radial/tangential shrinkage ratios are more prone to cup. I also stay away from open-pore species, though I have used black walnut successfully. I don't consider it to be a large open pore wood like ash or oak. In my opinion, hardness is a preference, not a necessity. Softer boards do wear out sooner, but you might chalk that one off to "personality."

Ellis

Re: Preferred cutting board woods?

#9

Re: Cutting board woods

Michael Bush

>Yup, quarter sawing is essential if you're not going to glue it up.

My mother has to this day a poplar cutting board her father (a complicated man in many ways but an old fashioned hillbilly who took a rough-and-ready approach to household needs) sawed off the end of a longer piece when she was about 14. (She's in her 70s now.) It has been bowed for as along as I can remember, and probably as long as she can.