Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Porter-Cable 310 Bit Removal

Posts

Porter-Cable 310 Bit Removal

#1

Porter-Cable 310 Bit Removal

Ken Bellock (Houston, TX)

>I have the Porter-Cable 310 laminate router, and it is a real joy to use. However, I had a 1/8" roundover bit in it over the weekend, and I had a real devil of a time getting it out of there when I was done! I guess this does not have a "self releasing collet" like the rest of my routers do, because bits just pop out of the others easily. Is there an easier way to get bits out of this, or can I replace the collet with a "self releasing collet"?

Thanks,

Ken

Re: Porter-Cable 310 Bit Removal

#2

Jesper, Denmark

Re: Porter-Cable 310 Bit Removal

Jesper, Denmark

>When you loosen the collet nut, give the nut a sharp rap with the wrench sideways and the bit usually comes out eay.

A little cleaning and a squirt of wd 40 before you put in the bit helps.

Re: Porter-Cable 310 Bit Removal

#3

Common problem

doug f, san clemente, ca

>Ken - just about everyone who has a 310 has the problem on occasion. Couple of things to try. A LIGHT tap on the side of the collet usually will release the bit. If not, GENTLE persuasion with a pair of pliers is a last resort.

When you get it out, I found that the following helped at lot:

1. Thoroughly clean the shank on your bits and make sure there's no burrs.

2. Clean the inside of the collet.

3. Put away your Superman cape when you tighten the bit in the collet. It only takes minimal pressure to hold nicely and over-tightening can freeze the bit almost to the point that's it impossible to get out. DAMHIKT!

Have fun.

Doug

Re: Porter-Cable 310 Bit Removal

#4

Re: Porter-Cable 310 Bit Removal

Jim Dillon

>Ken,

Same solution as mentioned by all the others. Love the router but, the first time this happened, I REALLY had a hard time extracting the bit (usually the 1/8 inch RO). Then I read on WC the trick regarding a light tap on the collet and that has worked ever since plus, as mentioned, not tightening so much.

Jim

Re: Porter-Cable 310 Bit Removal

#5

JL

Slight hijack - "Teflon spray"? Would it work?

JL

>I've been rehabilitating theatrical lights at the playhouse and I happen to have a few cans. Do you think "Teflon Spray" lubricant would work better? I figure it would "boil off" or evaporate like the WD-40.

Re: Porter-Cable 310 Bit Removal

#6

Thanks All!

Ken Bellock (Houston, TX)

>I'll tighten it just enough to hold from now on, and try the light rap on the collet when it does stick.

I love everything about the router! It feels perfect in my hand.

Thanks again for the help everyone!

Ken

Re: Porter-Cable 310 Bit Removal

#7

Re: Thanks All!

Glenn Madsen near San Francisco

>You should consider the replacement router base(s) from Pat Warner for this little gem, too. www.patwarner.com Money well spent on mine.

Re: Porter-Cable 310 Bit Removal

#8

Ellis Walentine

Be careful

Ellis Walentine

>... about tightening. Just as you can tighten the collet too much, you can also not tighten it enough. If that happens, you'll find your bit slowly inching out in the middle of a cut and you could ruin your workpiece, or worse.

Ellis

Re: Porter-Cable 310 Bit Removal

#9

Re: Thanks All!

Ken Bellock (Houston, TX)

>It's funny, I was just on the lee valley site, putting together an order to build one myself, and the price comes out to about the same as he asks for his bases already assembled. One thing I would have liked though is a clear base like his offset base, but with handles on both sides. I feel like that would give me a finer level of control for routing out the details in inlays.

Thanks for the link,

Ken

Re: Porter-Cable 310 Bit Removal

#10

Re: Porter-Cable 310 Bit Removal

Bill Houghton, Sebastopol, CA

>Worrying about the bearings, which are, after all, pretty small, I've been setting the nut on the bench after loosening it a bit before I hit it with the wrench. I think it's the vibration that loosens the collet, so having it sitting on the bench shouldn't affect the success of this approach.

Re: Porter-Cable 310 Bit Removal

#11

Re: Common problem

Victor Parisian

>Ok, so you are in the middle of a set of dovetails and the bit comes loose. Which is a bigger problem a bit that moves ever so slightly while doing dove tails or one that is difficult to remove?

My vote is to tighten the H e double l out of the collett and worry about the bit removal after the job is done. Ycasmhikt.

Victor - got a small shower this evening in Houston - finally

Re: Porter-Cable 310 Bit Removal

#12

Re: Be careful - From personal experence

Victor Parisian

>I presume...

Believe me I know this.

After the router is thrown across the room, there is no further problem extracting the bit.

Victor

Re: Porter-Cable 310 Bit Removal

#13

Re: Porter-Cable 310 Bit Removal

Fred Davis

>I use a piece of hard wood to rap the router bit shank , not the router collet , this works well and does not damage the tool , like a wrench or a hammer or a flight acroos the room might.

FredD

Re: Porter-Cable 310 Bit Removal

#14

Re: Porter-Cable 310 Bit Removal

Kneale Brownson..Awaiting return to CO snows

>I'm with Fred. I've used the 310 mostly for roundover and have had a bit in it for months on end before needing to change one out. I've always tightened collets really securely since I had a bit come out of a different router years and years ago and go skating across the table. A good whack on the bit shank with a chunk of hardwood always has worked for me.