Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Need Pix of QS Sycamore Completed Project

Posts

Need Pix of QS Sycamore Completed Project

#1

Need Pix of QS Sycamore Completed Project

George@Colonel's Workshop-Havertown PA

>Good Morning Friends,

I am about to begin design and construction of a bedroom suite to replace one which moved out with my #3 daughter. We have an empty "guest" bedroom now.

I've been thinking about using QS sycamore for two reasons: I never worked with it so it'll be a new experience; by reputation, sycamore is beautiful.

Can anyone post a pic or two which shows fleck, color, texture of a sycamore item? Also I'd like comments as to how well it works/machines. Thanks.

George

Re: Need Pix of QS Sycamore Completed Project

#2

Click *LINK*

Mark Mandell - Gone Round In Jersey

>Then click again to enlarge. QS is the middle plate.


Sycamore

Re: Need Pix of QS Sycamore Completed Project

#3

Re: Need Pix of QS Sycamore Completed Project

Ken Oakley-Sunny St. Cloud, Fla.

>Don't have a finished project but here are some 1/4 sawn pen blanks


img

Re: Need Pix of QS Sycamore Completed Project

#4

Re: Need Pix of QS Sycamore Completed Project

Ken Oakley-Sunny St. Cloud, Fla.

>more


img

Re: Need Pix of QS Sycamore Completed Project

#5

Re: Need Pix of QS Sycamore Completed Project

DaleLenz

>Good afternoon, Col.,

I've worked a fair amount of sycamore, is quite interesting wood. I purchase my lumber local: green rough sawn so my information is based on those conditions.

1. Our sycamore, in E. Okla. Has quite a few bug holes, think it could be Ambrosia beetles. What you see is the brooding chambers with compartmentalization around the bug holes, tree's method of keeping the rest of the tree free of total infection. I fill the holes with blacken epoxy, looks great I think.

2. When hand planing, QS sycamore likes to fuzz, fuzz sands off. Used my low angle bevel up L/N Jack plane the other day on some QS sycamore and not much fuzzing.

3. In my opinion, QS sycamore though out the project is too busy of a look. I'd suggest you look at using only QS sycamore for the trim, facing material or the interior panels.

4. Have used oil, varnish, shellac and lacquer as seperate finishes along with combintion of the finishes, not really sold as one is better than the other. Just shipped out a piece that I filled the grain and put an ultra high sheen, okay, nothing to complete with the annual woodworking award, IMO.

I agree sycamore is a great wood to use, much of our sycamore lumber goes to pallets, : "(.

Enjoy the new project. Dale

Re: Need Pix of QS Sycamore Completed Project

#6

Re: Need Pix of QS Sycamore Completed Project

Fred Davis

>Morning George,

How about a drawer side or a board,

Sycamore is my favorite wood for drawer side , it has a tendency to chip a little aaround the flecks , but well worth the little extra effort.

FredD

Re: Need Pix of QS Sycamore Completed Project

#7

I Hear You, Dale. A Question???

George@Colonel's Workshop-Havertown PA

>Good Afternoon Dale,

I guess business of fleck within the whole furniture item WAS in the back of my mind, and perhaps contributed to my need to see what it would look like. As the furniture pieces require panels for tops and sides, and drawer fronts, there is opportunity to combine with another specie, and that may have a cost benefit besides. What would you suggest for the other specie? Most of my recent stuff has been cherry. I have had modest luck, but it now gives me a bad and very itchy skin reaction.

George

Re: Need Pix of QS Sycamore Completed Project

#8

Re:Actually,.. *LINK*

DaleLenz

>I meant to communicate: use face sawn sycamore with the QS. Use QS as facing or panels/drawer facing but not all QS for whole project, too much for my eyes. I use black walnut with my sycamore flag cases, see link below. Theres a hyperlink on my "information" page that has an over-exposed sycamore case with cherry(?) splines, keys. The sycamore flag case on my website appears to have QS sycamore on the sides, I normally use QS for the flag case's facing material. When choosing rough sawn lumber, it's difficult for me to see the grain figure before planing, use what I've got, kinda lazy, : ' >. Need to look at end-grain more, many of my sycamore boards have both QS and face sawn on the same face. Sycamore lumber is loaded with ray-flecks of various degree.


Sycamore flag case

Re: Need Pix of QS Sycamore Completed Project

#9

I recently completed a single drawer for a friend

Victor Parisian

>who bought a dressing table missing a drawer. I found it easy to work, very attractive, but as others have said rather busy. I suggest you visit the local wood purveyor and buy a couple of boards to play with.

Sorry I didn't get a picture of the drawer before I mailed it off.

Victor - burning up in Houston

Re: Need Pix of QS Sycamore Completed Project

#10

Re: Need Pix of QS Sycamore Completed Project *LINK*

charlie belden

>Fine Woodworking "How To Design Furniture From Classic to Contemporary" magazine, on newstands now, has a 110" longside board that uses quarter sawn Australian silky oak that looks a lot like quater sawn, medullary rayed sycamore. QS sycamore with medullary rays looks like lacewood.

With four or five hand rubbed coats of shellac it's gorgeous.

Sycamore moves quite a bit and the "lacewood" figure is proned to easy tear out while planing.

Don't confuse sycamore with "english sycamore", the latter actually a maple. English sycamore, quarter sawn, doesn't have the medullary rays common to actual sycamore, but can have some really nice fiddle back and flame figure.

QS sycamore - with the lacewood look - is tricky to incorporate well in a piece of furniture. A few panels in a larger piece can be nice accents. But a piece made totally from QS sycamore would have, I believe, too busy and distracting a look.

Try it in a small box to get a feel for it and then think about incorporating some in a full sized piece of furniture.


Third Pic - lower right corner

Re: Need Pix of QS Sycamore Completed Project

#11

with cherry

Tom Sontag - St. Louis

>I think sycamore works well with cherry.

Photobucket

Photobucket

Re: Need Pix of QS Sycamore Completed Project

#12

Thanks Tom

George@Colonel's Workshop-Havertown PA

>Good Evening Tom,

That pix says it all, illustrating everything said in response to my post. It does work well with cherry. So I will revise my plans, and let my fingernails grow a bit longer to cope with cherry's skin reaction. And, I can incorporate off cuts into pen blanks for next Christmas.

George

Re: Need Pix of QS Sycamore Completed Project

#13

BTW, Nice Box Joints

George@Colonel's Workshop-Havertown PA

>

Re: Need Pix of QS Sycamore Completed Project

#14

Very nice Tom. Colors go good together

Victor Parisian

>and nice box joints there.

Victor

Re: Need Pix of QS Sycamore Completed Project

#15

Sorry I'm Late - Here's one

David Yoho

>George, a bunch of years ago I went to Barbara Gill's and purchased a good amount of QS Sycamore. The plan was to use it for drawers on special case pieces I might build over time.

When I built several of my Shenandoah blanket chests last year, I used it to make the entire drawer boxes, minus the fronts. I employ a technique for making the fronts look like a solid 3/4" front by cutting two pieces; one 1/2" for the drawer box front, and one 1/4" piece for the false drawer front. This makes it very easy to cut my through dovetails in my drawer parts. Once the drawer is assembled, I glue the false front to the front of the box and tack it with a pinner from the inside. The end result looks like a 3/4" rabbited front - making the dovetail process very easy.

The picture shows the QS sycamore side of one drawer where it meets the drawer front. The chests were made of Tiger maple and the sycamore added a little pizazz when the drawers are open. I even made the solid bottoms from it, as well.

I like it for drawer stock but, personally, I don't know if I would want to use it for an entire case piece. It is very easy wood to work with and I've found it stable due to quarter-sawing.

David


img

Re: Need Pix of QS Sycamore Completed Project

#16

Additionally

David Yoho

>I didn't make it clear but I made the fronts from the wood of the main case. In this case it was Tiger maple. The remainder of the drawer boxes were QS sycamore.

Re: Need Pix of QS Sycamore Completed Project

#17

Re: Need Pix of QS Sycamore Completed Project

Jim Dillon

>George,

Sorry, I'm late to the parade as well. Here is a pic of QS sycamore with jatoba. The finish is T&T oil/varnish. Not sure why the bottom three drawers are lighter and less uniform in color, but that is the only pic I could find. The color on all the drawers is actually like the top drawer and is quite uniform, especially after five years. I found it to be a soft wood (well, anything compared to jatoba is "soft"), and had real problems with cutting dovetails in it, but that is likely due to my poor sharpening skills (and talent). If I did the finish over, I would likely apply a seal coat of blond shellac first, then the T&T - just to give it a tad more shine. I think it would look great with cherry.

Jim


img

Re: Need Pix of QS Sycamore Completed Project

#18

Re: Need Pix of QS Sycamore Completed Project

Rickey LoDico------WebKitFormBoundaryAZXq5wtv+MOO2

>This is the only thing I've ever done with it and looking at it now, it appears that I should have taken a little extra care at removing the glue from the corners. At least I never applied a finish.


img

Re: Need Pix of QS Sycamore Completed Project

#19

Re: Need Pix of QS Sycamore Completed Project

bill sams

>also late to the topic, but just posted pics in the message above regarding sycamore drawer slides