Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Work in process

Posts

Work in process

#1

Work in process

Clint Searl, at the base of Haycock Mtn

>This slab of cherry is going to be the floating top on a base of patinated copper tubing. It's 69 1/4 x 36. Finally to the point of sanding, scraping, and sanding off all the planer marks and oxidation. Part natural edge, part molded edge. The butterflies are pau amarillo. Splits on the underside filled with Bondo so the splits and knot surrounds on the top can be filled with epoxy containing copper powder. The little knot hole on the left will get expanded to receive the polished flat half of an amonite sitting flush with the surface.

Clint


img

Re: Work in process

#2

Related tool comments (Long)

Clint Searl, at the base of Haycock Mtn

>Removing the planer/sander washboard and oxidation and final sanding represented lots of hours over more than a week, employing a 3x21 belt sander with 36, 50, and 80 grit paper; a Kunz scraper plane, a 5" ROS, hand scrapers, a 1/4 sheet sander, and hand block sanders.

The belt sander is great for leaving its own ripples and a heavy scratch pattern that the 80 grit doesn't do much against without clogging and dulling quickly.

My skill at sharpening and adjusting the Kunz leaves much to be desired, so while it was moderately useful, between the tendency to chatter and constantly fussing with it, I moved on to a hand scraper in a fancy clamping holder with an adjustable bow screw.

That was a waste of time, since it's much easier and quicker to simply use a scraper by hand, finessing the angle and bow to generate those fine little curls.

I bought a Bosch 1/4 sander to replace an ancient B&D that lost its jiggle and was a pain to mount paper on. The Bosch takes paper with a clamp arrangement that pulls the paper tight as it clamps up.

As for paper, I had bought some Norton 3X 100 grit to try out a while back. Either in the 1/4 sheet or on a hand block, it's the best paper I have ever used: agressive and long lasting. So I dropped by HD and picked up packages of 80, 150, and 220. They are all great.

The rest of the project is downhill from here.

Clint

Re: Work in process

#3

Re: Related tool comments (Long)

Tom Pilsbury (Chicago)

>Wow! What a beautiful piece of wood. I just finished reading Nakashima's "Soul of a Tree" this morning. Looks like you're channeling the esteemed woodworker. What do you plan for a finish?

Re: Work in process

#4

Just clear NC or alkyd lacquer

Clint Searl, at the base of Haycock Mtn

>

Re: Work in process

#5

Re: Related tool comments (Long)

Barry Irby

>Did you make the top surface FLAT or is it somewhat naturally contoured? This is a job that one of the the big industrial belt sanders would have done in short order. I have a friend with a cabinet shop who would have done it in about an hour. But, that would have taken all the fun out of and left it dead flat.

A question on your butterflies. One of them appears really long. I've never done any and I have never seen any that long. Are you concerned about the "cross" grain connection?

Re: Work in process

#6

Belting

Mark Mandell - Gone Round In Jersey

>Such work with a 3x21 cries out for a sanding frame. I use my Ryobi worm-drive with the adjustable frame for such things and can take the finish off birch ply and still have veneer when I'm done. Take it down at 45� to the grain then finish up with the grain with a progression through the grits and it leaves little for the RO etc. to do.

Re: Work in process

#7

Re: Related tool comments (Long)

Clint Searl, at the base of Haycock Mtn

>Across one diagonal it's flat; across the other there's aabout a quarter inch dish. Afer five or six year's seasoning, it's not going to move any more, and rather than obsess over it, we'll learn to love its warped personality.

The big butterfly is 12 inches long. The split isn't going to open any more and I doubt that the embedded 6 inches on either side will have any problem. We'll see.

Clint

Re: Work in process

#8

Re: Related tool comments (Long)

Barry Irby

>Thanks.

I have a table that has a single pine board top about 32" wide. A friend made it for me over thirty years ago. Where I sit every night for dinner my plate sits flat about half the year and the other half it rocks. The top warps and unwarps with the seasons. The wood never dies.

I am going to have to do some butterflies. I like them. Thanks again.

Re: Work in process

#9

Re: Belting

Barry Irby

>Are you speaking of one of those frames that fits around the beltsander? I assumed they were useless. You have one and it works well? I wonder if one is available for my sander?

Re: Work in process

#10

Re: Belting

Clint Searl, at the base of Haycock Mtn

>I assume that the frame keeps the action planar, so if there's any twist, belly, or dish, material has to be differentially removed to flatten the surface. That could make the perimeter edge vary in thichness. Having recently gone through that with a router frame setup on a twisted 52" diameter maple glueup that was varying the edge thickness by more than 1/2" before I decided to convert it to firewood, I decided that there's some out-of-flat that I can live with.

Clint

Re: Work in process

#11

Procedure

Mark Mandell - Gone Round In Jersey

>It's not a thickness planer but, used along with a 3' straight endge, it'll give you a flat surface.

I have a router frame for stuff up to 28" wide that I have done with a planing bit. Key is the reference surface base being flat. If your board is twisted, I think you're better off to rip, plane, joint, and rejoin.

TJMO YMMV

Re: Work in process

#12

Re: Procedure

Clint Searl, at the base of Haycock Mtn

>"Key is the reference surface base being flat. If your board is twisted, I think you're better off to rip, plane, joint, and rejoin."

As a matter of personal preference, I'd just do the glueup with dimensioned lumber to begin with.

Clint

Re: Work in process

#13

So True

Mark Mandell - Gone Round In Jersey

>But then along comes that special slab with all the swirling grain . . . . . |;-}}}}}}