Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Repairing Old portable Circular Saw Questions.

Posts

Repairing Old portable Circular Saw Questions.

#1

Repairing Old portable Circular Saw Questions.

Barry Irby

>I have an old B&D Builder's Sawcat (Skill Saw). It has gotten to where the blade will spin on the shaft. That is, the washer held on by the bolt fails to secure the blade to the shaft and allows it to slip.

I think two things have caused this. Over time, the washer has flattened and is no longer slightly dome shaped. The central part of the washer comes into hard contact with the end of the shaft before the flange of the washer locks the blade. And/Or the blades are slightly thinner than they used to be, ending up with the same result.

I tried to buy a new washer, but the tag is long gone off the saw and apparently they made about a dozen versions of it. A local (Non B&D) repair shop would not hazard a guess as to which one I might need or even if they were all different or the same. I have not been able to get to the B&D repair shop during business hours.

A result of the blade slipping is that the shaft is worn and the blades no longer fit snugly on the shaft.

What do you think of the idea of grinding about a 1/32" or even a 1/16" off the end of the shaft to compensate for the flattening of the washer? Or would it be better to grind the recess in the washer a little deeper? Or should I just hunt down the repair shop and get the right washer?

Could I build up the diameter of the shaft with something like JB Weld?

The saw is like an old friend and I earned my living with it for years, but I really don't want to spend a lot trying to repair a lost cause. Not sure how much life is left in it even with repairs. It's probably thirty five years old.

What saw would you buy as a replacement? I am not looking for a $19 HF special. Another "real" saw that will get the job done when asked. OTOH, times are tough and I can't afford a new best friend.

Re: Repairing Old portable Circular Saw Questions.

#2

Re: Repairing Old portable Circular Saw Questions.

Phil Joines Krum,Tx

>Why not make a shim washer to go under the regular one?

Re: Repairing Old portable Circular Saw Questions.

#3

Re: Repairing Old portable Circular Saw Questions.

Barry Irby

>I considered that. Don't know why I am reluctant. The only thing that comes to mind was that it would be another thing to keep up with while changing of the blade, but that doesn't make much sense. Don't change the blade that often.

Re: Repairing Old portable Circular Saw Questions.

#4

Re: Repairing Old portable Circular Saw Questions.

David Yoho

>Barry, don't give up your old friend until you check either the factory service center on Dabney Rd. or Staley Tool Company over behind the main post office. One of those places should be able to help when you get the time.

Re: Repairing Old portable Circular Saw Questions.

#5

Re: Repairing Old portable Circular Saw Questions.

Barry Irby

>Thanks David. It was Staley that tried to send me to the Factory service center. I did not have time to go there at the moment and I am working out of town five days a week now. I will try the service center this morning, but I am assuming they are closed on the week ends.

Re: Repairing Old portable Circular Saw Questions.

#6

Re: Repairing Old portable Circular Saw Questions.

ehgauss

>The cupped washer that's flattened out is called a "Belleville Washer". McMaster-Carr has a whole selection of different sizes and configurations available. Check "http://www.mcmaster.com/#metal-belleville-spring-washers/=2p4z82". Their shipping is reasonable, their service is quick and very helpful, and they've never been out of stock on anything I needed yet.