Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Leveling Stool Legs..

Posts

Leveling Stool Legs..

#1

Leveling Stool Legs..

David Winters

>o.k.- this is weird..

Just made a set of five bar stools, and the legs aren't even. Set the stool up on the tablesaw, which I figure is the most even surface around.

So the legs always are high on two diagonal legs, and I'm touching the high legs on the stationary disc sander. I can get the legs even, but if I rotate 90 degrees then they aren't... Same if I put them on the concrete slab floor. Makes no sense to me.. what am I missing? What's the best way to do this?

Thanks in advance.....

Re: Leveling Stool Legs..

#2

Sounds Like

Mark Mandell - Gone Round In Jersey

>It's time to check and adjust your saw table.

(I use a piece of MDF as a reference surface to level legs)

Re: Leveling Stool Legs..

#3

Re: Leveling Stool Legs..

Barry Irby

>Lets say you letter the legs so that they are marked North, South, East and West, so that North is diagonally opposite South and East is opposite West, and you set the stool on a truly flat surface, if East and West are short, they should remain short no matter how you rotate the stool. It seems to me, if the relationship changes, the surface MUST not be flat. How much are you dealing with? If you are talking about 1/32", you might not see the warp in the table. OTOH, if you are talking 1/4" I would think it would be clearly visible. I think you can test your flat surface with your stools. Mark or clearly note the two long legs. Then move the the stool around and rotate it. If the legs seem to change either your stool is really flimsy or your surface is not true.

This is why I like things with three legs. Three points establish a plane. They may not set level, but they never rock.

Re: Leveling Stool Legs..

#4

Three legged stools or matchbooks

Clint Searl, at the base of Haycock Mtn

>

Re: Leveling Stool Legs..

#5

Level the seat 1st

Philip Duffy

>-Put quarters under the legs to make the seat level in both planes.

-Mark each and every leg with a scribe/marker to a certain distance above the table.

-Cut all the legs at the mark, with an angle that matches the floor.

Voila! A level stool!

Re: Leveling Stool Legs..

#6

JL

Re: Leveling Stool Legs..

JL

>Sort of like Phil does his.

I have a reference table that is leveled (it is my cabinet saw). I have wooden wedges in various slopes. I put a level on the stool top in one direction and level it with the wedges under the legs. I then put the level perpendicular to the first direction and use the wedges to level it in that direction. I sometimes have to level several times.

I then take an Accuscribe and draw around the leg bottoms using the cabinet saw top as my base. I set the Accuscribe to the highest leg. I then saw the legs off. If you don't have an Accuscribe, take a piece of hardwood ~3" long and about 2" high that is level on the top and bottom - mount an "eye" bolt through it. Make sure that the "eye" bolt can take a pencil. Use it to mark your legs.

Re: Leveling Stool Legs..

#7

Re: Leveling Stool Legs..

john lucas

>I do the same as the others but my legs are usually close enough I can just lay a pencil flat on workbench (which has been checked flat) and draw my lines. I also keep the little short pencils from the golf course. If the line created by a normal pencil is too high I simply carve off one side of the short pencil so it marks where I want. Maybe one of these days I'll make an official marking tool but this has always worked.

Re: Leveling Stool Legs..

#8

I use the vertical jointer.....

Barry Irby

>My router table is the wing of my TS. I set a bit in it about a 1/32" or more above the table. Then I determine which leg I want to cut off and slide it over the bit until the bottom is cut away. You can leave a tiny piece in place to support it and a single stroke with a rasp will take that off. I check again and trim again or trim another leg as necessary. I also use this technique to cut the feet on footed bowls. If the tip of the leg is small and might fall into the hole the bit comes through, I put a blank top on the router table with a hole that just fits over the bit. Seemed awkward, but works great.