Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Marquetry adhesive????

Posts

Marquetry adhesive????

#1

Marquetry adhesive????

Kneale Brownson..Awaiting return to CO snows

>My wife has some favorite marquetry objects acquired many years ago where the veneer has lifted off the substrate, which appears to be some sort of interior plywood.

It LOOKS like the adhesive used was some sort of contact glue.

In some cases, large sections of veneer are loose, in others, the edges are coming loose.

How would I repair this?

Re: Marquetry adhesive????

#2

Re: Marquetry adhesive????

Clint Searl, at the base of Haycock Mtn

>The glue might respond to heat, in which case you could iron the veneer back down. Otherwise, yo no se.

Clint

Re: Marquetry adhesive????

#3

Re: Marquetry adhesive????

Kneale Brownson..Awaiting return to CO snows

>Thanks, Clint. I did try a heatgun on the glue and it didn't make it become tacky.

Re: Marquetry adhesive????

#4

Lee Grindinger

Why contact?

Lee Grindinger

>Kneale, please describe the glue better. What color? Where is tha failuure..., in the glue itself? (Is there glue on both substrate and veneer?? from the substrate? the veneer? Is it hard and brittle or soft and pliable?

Re: Marquetry adhesive????

#5

Re: Why contact?

Kneale Brownson..Awaiting return to CO snows

>Glue is very thin and almost colorless. It is totally dry and just a bit rough to the fingertip. It appears to have been thicker on the veneer than on the substrate.

I was thinking some sort of contact adhesive because there appears to have been a thin layer on the back of the veneer and an even thinner one on the substrate, and there were slightly brownish bits of adhesive where the veneer over the edges of the plywood were joined to the thin layer of cork the maker put on the back of the plywood. My thought was one of those human-environment safe contact glues that have proven to be less effective than the more hazardous original types of contact adhesive. How long have the more friendly types been around? These were made in the 1980s, I think.

Re: Marquetry adhesive????

#6

Re: Why contact?

Glenn Madsen near San Francisco

>What you describe does not sound that different from a hide glue of some sort...

Re: Marquetry adhesive????

#7

Lee Grindinger

It's bad news if it is contact adhesive

Lee Grindinger

>There are no real repairs you can do to old dried out contact. The early ones were based in the acetone family and could be thinned/activated/reactivated with lacquer thinner or acetone but if it is that stuff that ship has sailed. it's well beyond it's reactivation phase. If it's early latex it's a miracle it lasted this long! That stuff was worthless. There were quite a few whose objective was to make a decent product that would no blow up a house or shop. They succeeded but it still sucked as far as toxicity to humans.

You're in a tough spot. Re-gluing is the best option but a tough one to do since parts of the marquetry sheet are still stuck. Regular wood glues need to contact wood fiber to work and if it's coated with contact cement the wood is effectively sealed.

Try this in an easy place. Clint suggested heat. Moisten the glue first, it's just possible you're seeing a wood glue and moisture along with heat may re-bond it.

Good luck,

Lee

Re: Marquetry adhesive????

#8

Re: It's bad news if it is contact adhesive

Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6

>I did some loose veneer repair on the ends of some church pews that was laid up with some kind of glue that seemed to have suffered from a short working life also.

It sounds like your description was like this stuff was.

What I did, was to slip a piece of sandpaper in between the substrate and loose veneer. I would then press on the front while pulling the paper out. This brittle glue turned to powder easily. I then blew out the dust, then worked the medium viscosity Cyanoacrylate into the space with a scrap piece of veneer.

I had a block of 3/4" mdf which I had covered with the thin packing tape to use as a platen. I held the veneer out and gave it a quick shot of activator, then quickly pressed it down with the platen. The glue is cured in less than a minute, and has pretty good bridging strength.

Have a rag handy to soak up any run-out, but be careful and wear gloves, because it gets hot enough to smoke when it cures.

If there is a good finish on the face, it can be chipped off with a blade.

Re: Marquetry adhesive????

#9

Re: Why contact?

Kneale Brownson..Awaiting return to CO snows

>Wouldn't hide glue soften with heat? When I heated either the veneer or the substrate, the adhesive remained dry and hard.

Re: Marquetry adhesive????

#10

Re: It's bad news if it is contact adhesive

Kneale Brownson..Awaiting return to CO snows

>I didn't use moisture when I tried heat, so I'll take a crack at that.

Re: Marquetry adhesive????

#11

Re: Marquetry adhesive????

Fred Davis

>Squirt little lighter fluid behind the Veneer , if it is contact cement , it will pop loose immediately.

The problem then will be cleaning it off enough to bond back with hide glue.

FredD

Re: Marquetry adhesive????

#12

Lee Grindinger

Keith has a good plan

Lee Grindinger

>

Re: Marquetry adhesive????

#13

Lee Grindinger

Yikes! No

Lee Grindinger

>Do not do this, Kneale, it will make it nearly impossible to glue it back down because of the oils in the lighter fluid. Acetone or lacquer thinner will have the same effect without the oils.

Re: Marquetry adhesive????

#14

Re: It's bad news if it is contact adhesive

Kneale Brownson..Awaiting return to CO snows

>Moisture and heat did nothing, so I guess it's Keith's approach.

Thanks.

Re: Marquetry adhesive????

#15

Acetone

Kneale Brownson..Awaiting return to CO snows

>When I rub the exposed adhesive with a white cloth wet with acetone, I get a yellowish residue on the cloth, the surface becomes slightly tacky briefly and then is smoother.

Re: Marquetry adhesive????

#16

Lee Grindinger

Acetone

Lee Grindinger

>Acetone will soften a lot of stuff so it's really not indicative of anything that your acetone softened whatever is there. I'd stick with Keith's approach testing it first in a small area.

Lee