Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Need pressure washer advice

Posts

Need pressure washer advice

#1

Need pressure washer advice

David G. Sparks

>I'm getting ready to buy a pressure washer and would appreciate any guidance you all can offer. I've read that the Honda engines and the Cat pumps are the way to go, but I could use some specific advice. I won't be using this commercially, but I would like to get a good one. Thanks!

Re: Need pressure washer advice

#2

Re: Need pressure washer advice

Ken Oakley-Sunny St. Cloud, Fla.

>Definitely Honda engine. Never paid attention to the pump on mine. It starts on first or second pull every time. Had mine for 8 years now.

Re: Need pressure washer advice

#3

Re: Need pressure washer advice

Doug Ridley

>Honda is what I have had for 3 years and it works good.

Re: Need pressure washer advice

#4

Jason Roehl in Lafayette, IN

Re: Need pressure washer advice

Jason Roehl in Lafayette, IN

>If you want one that will really last, a belt-drive pump is the berries.

In all the direct-drive units, the engine vibration will ruin the pump sooner or later. The more you spend, the later it will be.

Jason

Re: Need pressure washer advice

#5

There's Honda and then there's Honda

Mark Goodall - ATL - tooljunkie

>Unnderstand that Honda makes two lines of small engines. The GC series engines are good. The GX engines are their best. Other than the model numbers.... GC140, GC160, GC200, etc vs GX140, GX160, GX200, etc... you can usually tell the difference by the gas tanks.... plastic on the GC and steel on the GX series. The number in the model number refers to the cc size of the engine... like motorbikes.... gotta love Honda!

I bought my pressure washer 10 years ago at HomeDepot for ~$700. I use it less than a dozen times a year, but it always starts easily and has been a strong reliable perfomer. It has a GX200 (6.5HP) engine and a CAT pump. The pump is the blue one, made in Italy and was reportedly one of the best a most reliable pumps made. Mine is a DEVILBISS Excell EXPRO2530, but the brand really doesn't matter since just about all power-washer manufacturers are only assemblers, using components, engines, pumps from the major manufacturers.

The only problem with it... is that it is frankly too large and powerful. It takes up too much storage space, and is more powerful than necessary. It will destroy concrete if I'm not careful.

I often think about selling it and replacing it with one of those much smaller electric ones. The one I have is just overkill for cleaning the cars, dirtbikes, deck and driveway. This one is really meant for everyday use. Problem is that a new $700 washer sells for $300 used these days, which would just cover the cost of a smaller unit. It's in such good shape that it's hard to justify trading down like that. So I'm thinking of removing the GX200 engine to put in my daughters' gokart (they could use a better engine in their gokart), and replacing it with a smaller electric 2HP Baldor motor that I happen to have and making an overall smaller unit. Or maybe I'll just leave the engine in it, and cut the frame and try to make this one more compact in size. Or just build a second shed.

I have another GX engine on my son's racing gokart and that thing is awesome.

Happy Woodworking!


img

Re: Need pressure washer advice

#6

I've built a couple

Tim Greif - West of Chicago

>I built my own pressure washer. I then built another for my son. The one on the left below is over 15 years old. Cat pumps are the only way to go in my mind, although they too make pumps that are throw away variety. The pumps on the units below are commercial grade used commonly in car washes and carpet cleaning trucks. They are basically designed to run 24/7 on a continuous basis. You probably don't need that much in the way of heavy duty.

I'll let others address the engine type. I didn't want the hassle of running a gas engine every time I wanted to use it. These are full 2-horsepower motors that run on 220. I have 220 in the shop and enough extension cords to get me to the back deck. The 220 requirement also is a deterrent to all the friends and neighbors who think they want to borrow it.

You need to remember one thing if nothing else. Get a unit with at least 2.8-3.5 gpm capacity. Everybody gets hung up on pressure. I can create 1000 psi on a POS $100 pressure washer that's about as effective as the spray from a Windex bottle. Cleaning power is one thing - impact velocity and volume. Do not skimp on volumetric flow.

You control the pressure by changing the orifice size. Smaller orifice creates a higher pressure and higher velocity for the same flow. Since these are positive displacement pumps, the flow put out by the pump is fixed. Most decent washers have a bypass regulator that allows you to fine tune the amount of flow that goes to the gun, the rest bets recirculated back to the pump suction. Less flow through the wand orifice means less pressure (and less cleaning power).

The two units below put out 3 gpm at just over 1,000 psi and that's plenty good enough for anything I need. The last one cost me $700 just in materials to build.

Addy protocol: My family has been in the car wash business since the 60s.


img

Re: Need pressure washer advice

#7

Re: I've built a couple

David G. Sparks

>I like the pressure washers you made. I was a little concerned as to the cost of an extension cord long enough to do what I have to do. What gauge cord do you recommend for a 2 hp washer like your's?

Re: Need pressure washer advice

#8

Re: There's Honda and then there's Honda

David G. Sparks

>Thanks for the information. Do you know anything about the CAT triplex pump? I'm wondering if it's a good one.

Re: Need pressure washer advice

#9

Re: Need pressure washer advice

Michael Wilkins

>I have a PW with a Honda engine that used to start on the 1st or 2nd pull. Then I made the mistake of letting it sit all winter without putting Stabil in the tank. Don't do this folks. Taking the fuel system apart and properly putting it back together is a bear.

Finally got it checked out and now its running fine. I WILL remember to add a fuel stabilizer before putting it away for the winter.

Re: Need pressure washer advice

#10

I used 14 ga extension cords

Tim Greif - West of Chicago

>I used 14 gage wire for the cords. My pressure washers only draw a little under 10 amps at 220. There's nothing special about 220 volt extension cords except the connectors. Most are made using type SJT or SJTW cords. You can buy this in bulk. However, you're better off just buying a normal 14/3 cord designed for 115 volts and cutting off the ends and replacing them with 220 volt plug and receptacle.

The package will say the cord is rated for 125 volts, but that's because of the 115 volt connectors. The SJT cord itself has a rating of 300 volts. You can take a look at a bulk reel to confirm that if you are skeptical. Just keep in mind that if you make up your own extension cord, it has no UL listing so you can't sue anybody if something goes wrong :-)

Re: Need pressure washer advice

#11

Thanks for all the help!

David Sparks

>

Re: Need pressure washer advice

#12

Just the person to ask

Mark Goodall - ATL - tooljunkie

>Wow, you're jsut the person to ask.

I mentioned earlier that I have a Honda gasoline engine with my CAT pump, and have been thinking of moving the engine to a gokart (needs a new engine) and using one of my electric motors for the washer. I've got a couple of TEFC motors, one is 1.5HP and the other is 2.0HP, but both are 1725RPMs. The 2.0HP one has a flange that looks like it might match the CAT pump (direct drive). I see you're using a pulley and belt. What speed are your motors and what the gearing and final speed at the pump?

One goal in this would be to have a much smaller (physical size) unit, so I'd rather stick with direct drive, but I suspect that won't be possible.

Happy Woodworking!

Re: Need pressure washer advice

#13

Hmmmm...

Mark Goodall - ATL - tooljunkie

>"...CAT triplex pump...."

Hmmmm..... I think I recall "triplex" when I bought my washer. I know it's a CAT pump because research showed it was the best by far at the time. But it was 10 years ago and can't remember more than that. However "triplex" does ring a bell. Perhaps it refers to the number of cylinders in the pump or something like that. I'll take a closer look at the pump to see if there are any markings on it.

Happy Woodworking!