Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Keeping edges square when sanding

Posts

Keeping edges square when sanding

#1

Keeping edges square when sanding

mdclor

>Hi,

I have difficulty keeping edges square when sanding, especially on small parts for mission style clocks, etc. This is the case whether I use a ROS or hand sand. Therefore, I am looking for a cost effective solution.

How do you do this?

I have thought an edge sander (e.g. Jet EHVS-80CS) would be ideal, but might be cost prohibitive, so I also looked at a few combination sanders (e.g. Grizzly G1276). If you use either of these or a similar solution, what are your likes and dislikes? Any suggestions for similar machines?

Any other less costly suggestions?

TIA,

Merle

Re: Keeping edges square when sanding

#2

Re: Keeping edges square when sanding

Fred Davis

>A Oscillating drum sander wil do the trick, that's the most costly solution, Norm uses a drum sander attachment for the drill press , that's also effective and much cheaper and lastly ,I use a card scraper a lot on edges, leaves prettier surface then sanding and is fast.

I have a Boice -Crane Oscillator and mostly use it for curves.

FredD

Re: Keeping edges square when sanding

#3

I use my shopmade spindle sander *LINK*

Bricofleur

>I use my shopmade spindle sander. It's easy to build and cheap. I ordered few essential parts from Lee Valley. I use it on partically every project. By adding a notched fence to conceal the sanding drum, it is just great for sanding edges, straight.

Best,

Serge

www.atelierdubricoleur.spaces.live.com


img

Shopmade Spindle Sander

Re: Keeping edges square when sanding

#4

Ellis Walentine

Hand planes

Ellis Walentine

>A sharp hand plane will give you a much smoother surface than sandpaper, and you can check the edge with a try square as you work, making adjustments if necessary. A #95 plane has a built-in 90� fence to keep your edges square as you plane. A scraper plane is another option, especially for difficult woods.

If you're determined to sand the edges, keep in mind that edge sanders are usually set up with rather coarse belts, so I don't think of them as finishing sanders. For the finer grits, start with as square an edge as possible and use a solid backing block for your sandpaper.

Ellis

Re: Keeping edges square when sanding

#5

Re: Keeping edges square when sanding

Blackhawk6

>You could construct a jig to aid in hand sanding. Two pieces of 3/4" ply, one with a 1/8" by 1/4" deep rabbet along the long edge. Glue/screw the two pieces together at 90 degrees with the rabbet on the inside. Attach sandpaper to the side without the rabbet. The rabbet now is a groove to set the edge of the sandpaper into as well as a place for dust to fall. You could arrange the length of the boards to accommodate a sanding belt and use a small block of wood in the back for tension.

Re: Keeping edges square when sanding

#6

Gang the parts if you can...

John in NM

>and use a square 1/4 sheet sander. Works about as well as anything for mission spindles, and saves you a lot of time. Still tedious though, and works best if you take the time to make a jig. I often also end up using a sharp plane.

Re: Keeping edges square when sanding

#7

take care

Bill Tindall, E.TN

>I have struggled learning most hand tool operations but keeping an edge square wasn't one of them, which leads me to believe that this operation should be easy. I am presuming these edges are machined on a jointer so that they require only light sanding to remove glaze from machining.?. If not, then this a the place to start the process. A properly machined edge is so easy to sand that I would not consider using a machine to do it, ROS for example, which I know I could not control on an edge.

A stiff block is necessary. Other than that it is simply being careful and not getting in a rush pushing the block back and forth. I use a 2" wide block for these operations. The closer the block width to the edge thickness, the easier it will be to control the block.

Re: Keeping edges square when sanding

#8

Re: Keeping edges square when sanding

Ed Mulligan

>That rounded edge business is called pillowing. If you want to use a random orbit sander, get one that uses pressure-sensitive adhesive. The pad is much harder / firmer than loop and hook versions. That said, my Festool RO 150 with hook and loop pad does a great job.

As you near an edge, the sandpaper should overlap the edge only the smallest amount. If you overhang too much, you risk tipping the machine and rounding the edge.

If you are hand sanding, always use a sanding block. Just as with machine sanding, don't overlap the edge too much.

For solid wood, I usually plane off the machine marks, then scrape off the plane marks, then hand sand to achieve a uniform surface for accepting stain. It's much faster than machine sanding, and cheaper because you use little sandpaper. And, pillowing is not an issue.

When you are finished sanding the flat surfaces, the edges should be broken, in other words a tiny radius applied. This rounded edge allows finishes to retain uniform thickness near the edge, and makes the edge less vulnerable to dings.

Re: Keeping edges square when sanding

#9

Re: Keeping edges square when sanding

Alexander Grigoriev

>"and makes the edge less vulnerable to dings"

And also makes your knukles less vulnerable to dings!

Re: Keeping edges square when sanding

#10

Re: Keeping edges square when sanding

mdclor

>Thanks for all the tips. I think the parts in question are too small for planing, 1/2 x 5/8 x 3, but you got me thinking in a different direction. I can stick sand paper to a piece of glass I use for sharpening chisels and move the wood over the paper rather than the paper and cork block over the wood.

Not as much fun as a new machine, but definitely cost effective.

Thanks, again,

Merle

Re: Keeping edges square when sanding

#11

Not too small for planing...

John in NM

>Clamp a large hand plane upside down in a bench vise and use it like you would a power jointer. You can even make a little push stick - more to save your finger tips from bruising than the blade (I've never cut myself doing this). Plane does need to be quite sharp and set fine.