Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

OT - how to put a faucet on a plastic trash can?

Posts

OT - how to put a faucet on a plastic trash can?

#1

OT - how to put a faucet on a plastic trash can?

Joe in a Cleveland Suburb

>Hi.

I would like to put a spigot or faucet on the side of a plastic garbage can near the bottom. I'm going to put this under a down spout and catch rain water. The can will sit up on a base so I can put a pail under the spigot to fill.

I was at the borg over the weekend looking at all the options. Not being a plumber, not knowing what all is available, and not knowing how best to do it so it doesn't leak, I thought I'd ask you guys what to get. I just don't know what fittings and so on would be best.

I figure I might be able to save a couple dollars watering the garden by using rain water. Also, when the dogs do their business on the grass, I pour water on it (the urine) to help from burning the grass out - it actually helps a lot with three Golden Retrievers. It is such a waste to pour lots of expensive city water on it...

What exactly should I get? Suggestions?

Thank you.

Re: OT - how to put a faucet on a plastic trash can?

#2

Re: OT - how to put a faucet on a plastic trash ca

Ralph Lipeles

>Here's what I've done to do something very similar. Get a flange fitting with a thread size the same as the faucet. The flange will mount with 4 bolts. Cut a piece of rubber the same footprint as the flange with clearance holes for the faucet and the 4 mounting holes. Now, you will have to make a washer for the inside of the can. Thin metal like, 1/8" aluminum or maybe just another flange. Get some flat head brass screws and brass nuts. Lastly, cut the clearance holes in the can for the faucet and the 4 flange mounting bolts. Also, it will be easiest and last longest if you use a can with a flat side where the flange and valve will mount.

Re: OT - how to put a faucet on a plastic trash can?

#3

Re: OT - how to put a faucet on a plastic trash ca

del schisler

>i fixed one for the neighbor It was a barrel 50 gal So we couldn't get inside I used a hose bib a 1/2" and drilled a hole and screwed it in the barrel than i used a 2 part JB WELD which has been working for about a yr now It is solid But I wouldn't try and hang anything on it But a hose screwed on their and not pulling on it very hard wouldn't not hurt They make a gray hose bib also a plastic so maybe that maybe better ? both would work my 2 cents

Re: OT - how to put a faucet on a plastic trash can?

#4

Re: OT - how to put a faucet on a plastic trash ca

Chuck in ND

>I bought a plastic 55 gallon drum that has 2 threaded bungs in the top. My plan is to lay the barrel on it's side ontop of a stand, then after a few plastic fittings use the top bung for the rain water to go into, and the bottom bung put a valve in it. They sell a plastic valve that is made to fit those.

Re: OT - how to put a faucet on a plastic trash can?

#5

Re: OT - One more suggestion

Chuck in ND

>For the dog spots, Gypson works pretty well. We bought a 50 lb bag of it, and just hand sprinkle a little on the spots. Anyone that sells fertilizer should have it.

Re: OT - how to put a faucet on a plastic trash can?

#6

you may need to visit a plumping supply

Bill Tindall, E.TN

>1. If the plastic is thick enough (it probably isn't) you can drill an undersized hole and screw in a male pipe threaded faucet. The metal will make its own threads.

2. Go to large plumbing store and tell them what you want to do. What you need is a "bulk head" fitting on the faucet. These have straight threads upon which a nut and washer can be installed on each side of the plastic and thereby make a seal.

Re: OT - how to put a faucet on a plastic trash can?

#7

Some things to think about... LONG

Grant in Iowa

>Make sure your design includes an overflow route for heavy downpours. Make sure your overflow route can handle the capacity of the downspout. Suggest 3" PVC minimum. I see many "plans" for rainbarrel plumbing, but many of them have major flaws in their designs.

Think about:

-A way to drain it (and keep it drained) for winter

-An overflow route as stated above

-Elevating the barrel bottom at least a couple feet above the ground in order to obtain enough pressure to push the water through through a hose, if used. Figure .5 PSI per vertical foot of water fall. Normal house water pressure is usually between 60 and 80 PSI. As the level of water in your barrel falls, pressure will also drop. Enough water pressure to fill uckets, or even push the water through a hose on level ground, but you won't be using a garden sprinkler or hose nozzle.

-Link barrels together to add additional capacity. Put your pipe link from the bottom of one barrel to the bottom of any additional barrel. Vent the tops of the additional barrel(s)screen the vents to keep mosquitos out.

-Keep mosquitos out of your barrel(s) by using screening. Screening can also filter the grit from your roof so it won't end up in the barrel.

-Find out what the maximum rainfall on record is in your area. Then consider the area of roof your chosen downspout is draining (estimate), then do the math.... Example: a 10'x10' area of roof in a 1" rainfall will yield about 62 gallons of water (less if the roof pitch is higher). If you have a huge roof area, the collected water adds up fast: A 1000 square foot area can gather 620 gallons in a 1" rainfall. (Someone check my math here). Note that in most situations your 50 gallon barrel will be full quickly during a substantial rain. You MUST have a place for this water to go after that happens.

PLEASE PLEASE PLEASE locate your barrel in a secluded spot so your neighbors won't have to look at your creation. If we all keep such systems hidden or pleasing to look at, then such activity won't cause unreasonable laws to be enacted in the name of vanity.

FWIW,

Grant in Iowa

Re: OT - how to put a faucet on a plastic trash can?

#8

Re: OT - how to put a faucet on a plastic trash ca *LINK*

GalenV in Iowa

>What you need to ask for is a bulkhead fitting. Depending on the valve size you want will dictate the bulkhead fitting size.

They look like a threadded bushing with a nut. Along with that are two gaskets that sandwich the tank shell. You cut a round hole the "bushing" will pass through and the nut clamps from the inside with a gasket inside and out. There are suggested bulhead fittings per tank diameter so that the curvature can still be sealed.

Galen


One typical supplier

Re: OT - how to put a faucet on a plastic trash can?

#9

Trash can

GalenV in Iowa

>Forgot to say you had better be sure the trash can you buy can actually hold water. Some are "soft plastic" and they have little reinforcement. More than likely the tank will bulge out and possibly split out the side. Better to get a good poly tank designed to hold water. Yes more money.

Galen

Re: OT - how to put a faucet on a plastic trash can?

#10

Plastic drum...

John in NM

>We did this once when I lived in Tucson and had a flat roof with a parapet and two drainage points. Used blue plastic 55 gallon drums (it was just before y2k, so the drums were readily available due to end of the world fears!). In a heavy thunderstorm the drums filled in less than a minute and then had water shooting out the vent hole!

I elevated the drums about 30" and siphoned the water out using the garden hose. Real easy to prime, hook up to the hose bib, stick the other end in the barrel, and run the hose full of water, then fold the hose to keep it from running back out and unhook from the hose bib and head off to whatever needs the water.

The house was about 1200 sq feet, so it only took about 0.15" of rain to fill both barrels!

Re: OT - how to put a faucet on a plastic trash can?

#11

The Best is from Lee Valley *LINK*

Bricofleur

>Since you want the best, you will find it at Lee Valley.

This is the link to the article (#WT315) in their online catalog:

http://www.leevalley.com/garden/page.aspx?c=1&p=44757&cat=2,2280,33160

If you only need their installation instructions, use the following link.

Best,

Serge

http://www.atelierdubricoleur.spaces.live.com


img

LV Barrel tap installation instructions

Re: OT - how to put a faucet on a plastic trash can?

#12

Use a bilge pump instead

Clint Searl, at the base of Haycock Mtn

>

Re: OT - how to put a faucet on a plastic trash can?

#13

Jesper, Denmark

Re: OT - how to put a faucet on a plastic trash ca

Jesper, Denmark

>Go to a marine supply store and find a suitable size thru-hull fitting with a hose barb.

put on the barrel with the hose barb out, maybe a little silicone to make it tight.

Put a suitable length of garden hose on the barb, Make a hook from an old coat hanger and put on the hose. When not in use, hang the hose on the top of the barrel.

No moving parts other than the hose.

Re: OT - how to put a faucet on a plastic trash can?

#14

Re: OT - how to put a faucet on a plastic trash ca

dan arrowsmith

>Cheapest way is to get a rubber connection with stainless hose clamps used for repairing or joining to 1" plastic drain line. Drill a hole about the same size in the drum wall higher than the spot were the drum curves to the bottom. insert hose in hole then 1" line, the tight fit of the plastic line will seal the rubber connection against the hole in the drum , repeat as many times as needed to connect other drums tighten stainless clamp, it doesnt leak and i've used this system for years, cheap is good- I have free food grade drums for anyone in chicago

Re: OT - how to put a faucet on a plastic trash can?

#15

Re: OT - how to put a faucet on a plastic trash ca

James Runchey

>I have a plastic drum, in which I mounted a drain in the bottom, which I never use. I found it more convenient to dip from the top with a watering can or gallon milk jugs. Of course you can't reach the bottom with this method so I connected a couple of garbage cans in tandem since I need a lot of water living in the country, on very sandy soil. Last year I also bought an old horse tank to add to my water supply. I add "mosquito dunks" once a month to control any hatching in the water. We have lots of flower beds needing lots of water in dry periods, so this works out well for us.