Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Forrest WWII vs ????

Posts

Forrest WWII vs ????

#1

Forrest WWII vs ????

Terry Alexander

>I have the Forrest WWII blade and love it. I am just now starting my kitchen cabinet project and want a backup blade.

So, I defer to infinite wisdom of this board as to what blade is comparable to the WWII....hopefully at a lesser price.

As always....TIA

Terry Alexander in West Texas

Re: Forrest WWII vs ????

#2

Re: Forrest WWII vs ????

George@Colonel's Workshop-Havertown PA

>Good Morning Terry,

I like my WWII very much also. Its the best over all blade hanging on the wall peg. I use(d) a Leitz combination thin kerf for longer than I've owned my Forrest. After my furniture is all glued up, I'd be hard pressed to show you any differences between the two. No reason why you shouldn't buy another brand of premium blade as a back up. I use mine interchangeably. Kept sharp, they all do a creditable job.

George

Re: Forrest WWII vs ????

#3

Re: Forrest WWII vs ????

Rob Stokes in North Vancouver

>Sorry - but I don't get the economics here. You're building a kitchen and let's say you're going to spend $3000 on materials. A WWII is what - $110? And a "cheap" blade is going to run you about 1/2 that (if you're lucky). That means you'll be saving $60 or roughly 2% of your materials budget for a blade that you have no idea how it's performance is.

If you really like the WWII that much, why not get a second one?

Re: Forrest WWII vs ????

#4

Re: Forrest WWII vs ????

Terry in Edmonton

>I have WWII Dimar and CMT blades and I find they are all good IF they are properly sharpened. They all cut the about the same when new but had some problems with the WWII after it was sharpened, changed to different sharpening service and they cut better than new.

Re: Forrest WWII vs ????

#5

The same thing for less???

Ralph in Huntington Beach

>I could not agree more with Rob's assessment.

You want a cheaper blade that's comparable to the WWII...don't we all!!! My "back-up" blades are WWII's, but with a different tooth count. Most blades will cut just fine when new, but I believe that I get my money's worth out of the Forrest blades because they just stay sharp MUCH longer than other blades I've used. Spend a little more now and save money in the long run. You won't remember that you spent a few more dollars later, but you will notice that you wasted your money on a blade that's hanging on the wall and never gets used.

Re: Forrest WWII vs ????

#6

I love the Amana Prestige...

Brian in Sandusky, OH

>

Re: Forrest WWII vs ????

#7

Re: Forrest WWII vs ????

RonK

>Tenryu

I have a Forest WWII which hasn�t been on my saw in over a year. Tenryu has several different configurations optimized for cutting different materials so selection can be difficult if your local dealer doesn�t carry them.

As someone else mentioned Amana also has excellent blades.

The Forest are good blades but I feel there are many others that are just as good or better and most are at a more reasonable price though not necessarily cheap.

I should note that I don�t particularly like combination blades no matter who makes them so my opinion may not be applicable to your situation.

Re: Forrest WWII vs ????

#8

The PR1040 or the PR1040C ?

Terry Alexander

>

Re: Forrest WWII vs ????

#9

Re: Forrest WWII vs ????

Dave Paine

>On the topic of saw blades, there is no single solution for every cut in every material on every saw.

I have a Forrest WWII 40 tooth regular kerf and 30 tooth thin kerf. These blades produce the smoothest finished cuts. They are both ABT so if I need to cut a dado, they do not leave a flat surface.

If I am cutting thick dense stock such as 8/4 maple, I can get burning of the cut line, since I "only" have 1 3/4 HP motor, which limits my cutting rate.

I also have a Ridge carbide blade. This is 40 tooth regular kerf and does not burn as much. Likely due to better side clearance of the blade steel compared to Forrest. So I get less burning. It cuts well, and I feel a ready to finish cut, but to be honest, not as smooth as the Forrest. This is also ABT blade.

Forrest and Ridge blades cost about the same.

I also have a Freud blade forget the model number. This is thin kerf and 24 tooth. It was less than 1/2 the cost of the Forrest or Ridge. This is a flat tooth blade, so good for making dado's. It generates more noise when cutting, doe not make a cut as good as the Ridge, but the cut is flat.

So for dado's I use the Freud. FOr thick stock, I use the Ridge. If I want my best finish, I use the Forrest.

You pay's your money and makes your own choice.

I expect there are other good, perhaps better blades, just providing my experience on the few blades I own.

Re: Forrest WWII vs ????

#10

Re: Forrest WWII vs ????

Rob Stokes in North Vancouver

>Lemme know if you're selling the unused Forrest :)

Rob

Re: Forrest WWII vs ????

#11

Re: Forrest WWII vs ????

RonK

>I Probably wouldn't sell it. I don't do much cove cutting but if I do a combination blade seems to work best for me and it's the only combination blade I own.

Re: Forrest WWII vs ????

#12

Re: Forrest WWII vs ????

Nelson

>Try a Freud Fuison and you probably find you like it better than the Forrest, cost about $99

Re: Forrest WWII vs ????

#13

Re: Forrest WWII vs ????

Chuck in ND

>I guess I don't get all the hype about a Forrest blade, but then again I've never had one, or had the chance to use one. If I want what I consider is a good blade I usually buy a Freud, my father gave me a full kerf Systematic riping blade quite a few years ago that seems like a good blade also. I guess I don't consider myself as a exoctic fine furniture builder, never have, and not sure that I want to ever go that route. Most of the stuff I have done is fixing up antique furniture and refinishing them, or an occassional simple reproduction, or wall shelves, golf ball displays, quilt racks, garden arbors, trellis, etc. Don't get me wrong, I think precision is needed to get good glue joints, but sometimes I think it gets a little over blown and people spend more time tuneing machinery that was never meant for the tolerences they are looking for, then actually doing any woodwork.