Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

glue edge moulding to large panel

Posts

glue edge moulding to large panel

#1

glue edge moulding to large panel

steven E. Lewis

>I need to glue a 3/4" thick by 5/16" wide edge molding to decorative panels to be inserted into SubZero refrigerator/freezer doors. I am worried about applying the proper amount of pressure along the entire edge to achieve a strong glue joint with no gaps. I think this translates to the proper frequency of clamps so that there are no unpressured spots. Along the long edges (70") this could translate into so many clamps that they wouldn't all fit side by side, not to mention the fact that, by the time I got through tightening them the glue will have already set. I have contemplated using a my finish nailer, cauls and various types of clamps. I am afraid that the finish nailer won't exert enough pressure to hold tight unless I put a nail in every few inches which would make a mess of the edges (even though they are to be painted). I don't know if I can make a caul that is not prohibitively unwieldy for the long edge and I don't know what clamps to use (I think pipes would do, but how many and what spacing).

I would really appreciate any tips or advice. Thanks.

SEL

Re: glue edge moulding to large panel

#2

JL

Re: glue edge moulding to large panel

JL

>I've edge banded pieces of oak plywood that were larger. I made a caul by cutting a dado in a piece of 2 x 4 that I had ripped into a 2 x 2. I made the dado 3/4" wide and about 1/2" deep. The caul fitted over the edge banding (the joint was exposed). I had about 7-8 clamps over the 8' length of plywood. It seemed to work okay for me.

YMMV

Re: glue edge moulding to large panel

#3

Re: glue edge moulding to large panel *LINK*

Bricofleur

>Sel,

If you use cauls or wide boards between your clamps and your moldings you will need less clamps, so keeping the glue-up time shorter so the glue may not set before you are done. To read more about this, this is a link to the appropriate page of my website:

http://atelierdubricoleur.spaces.live.com/blog/cns!2ED8F7A23848B4AE!176.entry

Another way would be to delude your glue with about 5% water to give you more open time, assuming you are using PVA carpenters glue. White carpenters glue give your more open time also. Check the following link to my website to compare different types of glue you could use to deal with you working time issue.

Best,

Serge

www.atelierdubricoleur.spaces.live.com


Guide to Woodworking Glues

Re: glue edge moulding to large panel

#4

Ellis Walentine

Couple things *PICS*

Ellis Walentine

>Think of the pressure from your clamp pads radiating out at 45� angles from the pad. If you apply the clamps directly on a skinny edgebanding, you're right, the clamps would have to be right next to each other for the pressure to be distributed evenly along the glue line. As others have noted, a caul distributes the pressure so you need fewer clamps. The wider the caul, the fewer clamps you need, provided the total pressure they produce is enough to close the joint adequately. (If your edges are straight and square and the banding is planed smooth and straight, you won't need much pressure, so a few clamps will do the trick, as long as the caul is wide enough.)


Now, here an old guitarmaker's trick for glue ups like this using *no* clamps at all... Screw or clamp a couple furring strips to a work table, parallel and just slightly closer than the sum of the widths of your panels and edgebanding. Spread your glue on the panel edges, tape the edgebandings to the panels with a few pieces of masking tape to hold them in place, then place the whole mess between your furring strips with the edgebands back-to-back. Press the whole assembly flat to the table, and voila! A single sash weight will hold the glue-up down while the glue dries. The pressure you get with this method will depend on how accurately you arrange your furring strips.


Ellis

Re: glue edge moulding to large panel

#5

Re: glue edge moulding to large panel

pecker

>You could also just glue a thicker edge band piece on the panel. It won't need as many clamps.

When the glue dries, rip it on the table saw, down to the 5/16" dimension you wanted.

Re: glue edge moulding to large panel

#6

analysis of situation and how I do it

Bill Tindall, E.TN

>Theory: In the situation described, namely rigid panel, glue, flexible strip, clamps spaced on other side of strip, what is the distribution of force on the joint? In the hypothetical case where the strip is perfectly rigid, one clamp will uniformly distribute its force along the joint, In the other hypothetical extreme, perfectly nonrigid, the clamp force will not extend beyond the clamp edge. I believe, awaiting a mechanical engineer to properly calculate the situation using the stiffness of wood, that the force extends well beyond the 45 degree estimation commonly proposed.

In addition, optimum clamping pressure for yellow glue and panel joints is more than 100 psi, while for veneer 15 psi is adequate. I believe the edge band situation is closer to veneer than panel joints, so huge pressures are unnecessary for success in holding an edge band on. In any case I have not had one fall off. I think more than 100 psi at the clamp gets me at least 15 psi well distanced from the clamp edge.

What I do:

1. prepare panel edge to be straight, or as least don't have any abrupt gaps that would require the edge band to sharply bend to conform to the panel edge. The edge band must be smooth, but it is unimportant that it be straight.

2. Apply a bead of glue to the edge band. Rub edge band against panel edge to distribute glue on both surfaces.

3. Assemble joint- panel, glue, edge band and a caul. The whole assembly sits on the loosened clamps. I prefer a somewhat flexible caul so it can conform to any gentle curvature of the caul or panel. For this application I would use a 3/4-1" caul I keep on hand for these jobs.

4. Begin tightening clamps starting at one end. Align edge band as you go along tightening clamps. A clamp every 6" will do for the task at hand.

5. Look for squeeze out. Too much squeeze out will obscure this observation. A good squeeze out results from adequate clamp pressure. The 6" spacing enables an additional clamp to be installed if there seems to be a gap somewhere as evidenced by the squeeze out, or lack there of. .

For edge banding I apply the over sized band and let the edges hang over. They are trimmed flush later with a hand plane. I have been doing just this task on 1/4" x 1" cock beading on a project. In this case the bead needs to be precisely aligned. I have techniques for aligning.

Re: glue edge moulding to large panel

#7

just did one..... example

Bill Tindall, E.TN

>in order: clamp face, 7/8" walnut caul, cock bead, glue(not seen I hope), table skirt.

In this case I can't trim the beaded edge after gluing so there must not be any squeeze out at this edge. So, I look for the clamp pressure to bring the joint together with no gap.

In this case the clamp spacing is exactly 6". 12" was too wide and I had gaps, so I added a clamp in between to close gap. If force propagated a mere 45 degrees the gap would not have closed, illustrating a much broader lateral pressure propagation through the caul and cock bead strip to the glue joint.


img