Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Looking for nice 1/2" Cherry ply...

Posts

Looking for nice 1/2" Cherry ply...

#1

Looking for nice 1/2" Cherry ply...

Ralph in Huntington Beach

>As you can see from my name, I'm in HB Ca. I'm building a bed for my daughter and I need to find one (and only one) sheet of nicely figured 1/2" cherry plywood. The stuff I've found locally is pretty plain. They have some nicer...not much... 3/4", but I don't want the bed to weigh a ton and believe that 1/2" would fit the bill best. I can special order through them, but it's a pig in a poke and I can't pick out the sheet that I want! How do you all get around this without buying a 100 sheets to pick through?

TIA

Ralph

Re: Looking for nice 1/2" Cherry ply...

#2

Re: Looking for nice 1/2" Cherry ply...

Ed Mulligan, Cape Cod

>The plywood is for the headboard and footboard, I presume. You could use a sheet of 1/2" mdf or a good grade plywood (not from the home center) and apply your own veneer. This would really open up the design opportunities for you.

Re: Looking for nice 1/2" Cherry ply...

#3

JL

Re: Looking for nice 1/2" Cherry ply...

JL

>I agree with Ed. Find yourself some nice figured veneer. It is a lot easier to ship :).

Re: Looking for nice 1/2" Cherry ply...

#4

Re: Looking for nice 1/2" Cherry ply...

Clint Searl, at the base of Haycock Mtn

>The cherry ply that I have used was rotary cut and is almost as bland as phillipine mahogany. An architectural grade ply with a flat cut veneer would be more interesting, but expensive. As an alternative, consider ash ply with a cherry flavored stain.

Clint

Re: Looking for nice 1/2" Cherry ply...

#5

Re: Looking for nice 1/2" Cherry ply...

Ralph in Huntington Beach

>The bed I'm building is a kind of hybrid...a sleigh bed, made kind of like a day bad. So it will have two equal traditional headboard, foot board's, like a regular sleigh bed, but it will also have a back board that will be against a wall, and that's where I'd like the nice ply to go. Veneering was an option I looked at and I had two ways to do it...one, do it myself...something I've never done or cared to do! Or have it done at the place I buy my lumber (Austin Hardwood in Santa Ana, CA), but it was prohibitively expensive. I have the lumber to do a glue up, but just thought I might be able to find some nicer ply that would look...well, nicer. As you can see from the drawing, it's a fairly large area.

Ralph


img

Re: Looking for nice 1/2" Cherry ply...

#6

Re: Looking for nice 1/2" Cherry ply...

Ralph in Huntington Beach

>I'm not a fan of rotary cut veneers, but this was one case where I thought it might look better, but after reading your response I might have to rethink my choices. The cherry ply they have at the yard is not rotary cut, but is in fact flat cut. It looked ok, but kind of boring and I just thought I could find something more dramatic. Maybe I'll go back down there today and take a second look.

Thanks.

Re: Looking for nice 1/2" Cherry ply...

#7

Re: Looking for nice 1/2" Cherry ply...

Alex Grigoriev

>Another place you may want to check is Reel Lumber at the corner of N Kraemer and Miraloma in Anaheim (off fwy 91).

Re: Looking for nice 1/2" Cherry ply...

#8

Re: Looking for nice 1/2" Cherry ply...

Ed Mulligan, Cape Cod

>Veeery nice form. It cries out for custom veneer on the back board. Birdseye maple would look nice there. It goes very well with cherry.

Another option: cover the back board with fabric.

Good luck, whatever you decide.

Re: Looking for nice 1/2" Cherry ply...

#9

Re: Looking for nice 1/2" Cherry ply...

Ralph in Huntington Beach

>Thanks for your responses and helpful suggestions. I went where I should have gone all along, to Strata Forest in Santa Ana. Not only is it very close to where I live, but they had a much better selection than the "high end" place I first went to. Found a nice sheet that's made up from 10" wide strips of veneer with nice color. One of the guys there even helped me go through some of the stack before I found the one I was looking for.

Someday, if I ever finish it, I'll post some pics...

Ralph