Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

The Projects Within a Project

Posts

The Projects Within a Project

#1

The Projects Within a Project

Jim Shaver - Oakville, Ont

>¤t

The Projects Within a Project

Or is that The Battles Within the War?

Well my weekend Update on the kitchen...

Just kidding, I am finding out as I work through my kitchen renovation that there are more projects within this one that could stand alone as a project with all the same feelings of accomplishment when they are done.

Through this epic I have worked on three bathrooms and a laundry room during the Make Over of the house and I have not spent more time on any one step than the worrying about some changes I had to make in the kitchen. Here are my results.

One change that I had long wanted was to open up counter space by moving the microwave to above the stove. The existing cabinet was too tall to allow such a change to be made; it needed to be cut down from over 18 inches tall to 12 inches. That was simple enough, make a new box and doors. But the doors had to match the colour and the design of the existing doors. Such has been my anxiety for a few years looking at this. What could be the hardest part of the change, making an arched top was my worry, never having made them and thus a new learning from the process. But wait, there had to be a way for me to size the old doors and reuse them to make new ones, worst case use them as a template if I needed to go from scratch.

Photobucket

So I decided to see if I could re use them, careful cuts at the table saw and some careful disassembly was my key.

Photobucket

First I carefully cut the lower rail free from the doors, tapping the small stiles with a hammer I was able to cleanly break the cope and stick glue joints.

Photobucket

With some clean up work with a chisel I was able to clean the rail cope and then dry fit them back in to the doors, a super fit!

I then tapped out the raised panel, it was easy to do, but I found the panel had been centre set with two tint pin nails, my metal detector came in very handy and my careful extraction would be to the envy of any dentist watching me.

Photobucket

Once the panel was out it was simply to resize the length of the panel then route a cove that matched the rest of the panel and then reassemble the doors.

Photobucket

Photobucket

Photobucket

Photobucket

With the doors assembled and stain matched, I assembled them back to the cabinet and dry fit the box back in its place above the stove.

Photobucket

So far so good!

My other project was to make the door for the blind corner cabinet pull out hardware,

Photobucket

Photobucket

Jason was right, I will be going handle less on the sink base, the slide out will hit the existing handles, but I have a Plan B.

Photobucket

My next steps are to make two drawers with hand cut dovetails of course. I am excited as well; I am using the soft close Blum Tandem sliders, how fun, eh!!

Take care,

Jim

Re: The Projects Within a Project

#2

Re: The Projects Within a Project

Don Orr

>Nice work as always Jim. More counter space is always a good thing.

Re: The Projects Within a Project

#3

Re: If the handcuts are faster, t hen...

Glenn Madsen near San Francisco

>go ahead. But I found that the furniture maker takes over, when it's the cabinet maker's job, and the kitchen stays unfinished far longer than it needs to.

If you have a jig you trust, then go for it. We know you can hand cut dovetails. We've seen the saw till. ;-)

Re: The Projects Within a Project

#4

Re: If the handcuts are faster, t hen...

Jim Shaver - Oakville, Ont

>You are right Glenn,

The Furniture maker does take over, LOL....the drawers are already cut, took an hour and a half to make the two drawers I need by hand....

Take care,

Jim

Re: The Projects Within a Project

#5

You're fast w/ this project.

Hikmet C. Sakman -- Victoria, BC.,CDN

>

Re: The Projects Within a Project

#6

Re: You're fast w/ this project.

Jim Shaver - Oakville, Ont, Canada

>Dovetails are now a Cosmic Experience for me Chico... Just you Wait! Blum Blum Blum...

Take care,

Jim