Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Too thick for my drawers....

Posts

Too thick for my drawers....

#1

Too thick for my drawers....

B.K. Moring

>Not those drawers.....I�m making 12 drawers for matching his and her chests of drawers. In the past I�ve made drawers with sides 1/2" to 5/8� thick, out of 3/4 rough lumber. Joint, plane, no problem.

The only poplar available in my area when I was buying material was 4/4, planed on the two faces.

The two options I�m looking at are:

1) Jointing and then planing down to 5/8� and making a pile of expensive sawdust

2) Resawing and making 1/4� material for the drawer bottoms. (Past experience has shown me that resawing a straight board can give you two crooked boards with not enough thickness left over for jointing and replaning)

What is my best way forward. Any other suggestions would be appreciated. Thanks.

Re: Too thick for my drawers....

#2

JL

Re: Too thick for my drawers....

JL

>It is poplar. I presume it isn't that expensive (less that $2/board foot around here), but I could be wrong. If it was 5/4, I'd chance it. But with 4/4 - I'd make sawdust.

Re: Too thick for my drawers....

#3

now that's a problem

Bill Tindall, E.TN

>I think even 5/8" is too thick for a drawer side, 1/2" being optimum for many drawers and thinner yet for small drawers.

Resawing for bottoms seems a good idea. Don't fret if it isn't flat, as the drawer framing will hold the bottom flat and a 1/4" bottom will be flexible enough to squish flat into the drawer.

There isn't a place in the US that 5/4 or 8/4 lumber can't be found. Either can be resawed for drawers. Find a cabinet shop and be nice to the owner. Ask where they get lumber. They might even sell some they have on hand. One can use almost anything for drawer sides and a shop may have something on hand that they don't need.

Re: Too thick for my drawers....

#4

Re: Too thick for my drawers....

Barry Irby

>Why not buy ready made drawer stock? I was in a cabinet supply wholesaler some months ago and they had drawer side material made up with a groove and rounded edges, both plywood and solid wood versions. I'm sure thee are Internet sources. Of course, maybe somebody on wood finder has them.

Re: Too thick for my drawers....

#5

# 1 . . .

steve mackay

>I used to be in the same spot. Buy "dimensioned" red oak from The Borg or 4/4 from my lumberyard and pay to have it planed at a mill shop. That pile of dust DOES look expensive but a) still cheaper than The Borg, 2) WAY cheaper than ME trying to re-saw and trash the whole board !

Re: Too thick for my drawers....

#6

Glue up a larger blank...

Jim Rahbe

>B.K.

Like Bill, I like to make my drawer sides slightly less than ��, but if I wanted �� sides and could only find 1� material, here is what I�d do..

Glue up five 1� boards face to face. Joint one face of this blank. Resaw a piece slightly larger than �� and clean up with the planer. Flatten the blank using the planer (or jointer) and resaw another piece. Repeat process until you�re left with a piece to small to use.

The �sawdust method� gives you five sides out of five boards.

The �glue up� method gives you eight or nine sides out of the same five boards.

Not sure the costs outweigh the effort involved, but if you are cheap like me, or stuck with specific amount of material, it will work.

Regards,

Jim R.

Re: Too thick for my drawers....

#7

Re: Too thick for my drawers....

George@Colonel's Workshop-Havertown PA

>Good Afternon BK,

I'd buy 5/4 and resaw bottoms. Plane the sides to 1/2" or lighter.

George