Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Old Issue?

Posts

Old Issue?

#1

Old Issue? 

Mark Mandell - Gone Round In Jersey

>


img

Re: Old Issue?

#2

Re: Old Issue?

Randy Johnson Connersville IN

>QUALITY? power tool from Sears?

Re: Old Issue?

#3

Ahhhhhhhh, yes . . . .

steve mackay

>The two things ALL woodworkers LOVE to HATE ! Ol' Norm & Craftsman. Both are evil, wicked, mean & nasty. Low-rent, low-quality, low-priced & low-down. No one has ever owned or used Craftsman and no one has ever watched Ol' Norm and learned anything. : )

Re: Old Issue?

#4

Whoa! Steve . . .

Mark Mandell - Gone Round In Jersey

>That's Bob Veeeeeeela.

Can't say I've ever seen Norm pushin' Crapsman.

Re: Old Issue?

#5

Re: Ahhhhhhhh, yes . . . .

Randy Johnson Connersville IN

>I've owned a number of Craftsman POWER tools. Some were, at best, adequate. Some (a �Sears Best� 1/2 drill being the most memorable) were downright awful. I actually bought an identical drill in a garage sale thinking that mine was a fluke. It wasn�t. I was in my early twenties at the time, but even at that I should have known why the guy was selling an almost new drill so cheap.

I still have and use Craftsman wrenches - but I�m only an occasional user of them. If I made my living as a mechanic I might opt for another brand. The handheld power tools I prefer are Milwaukee, followed very closely by DeWalt. In my experience, and granted one person is not conclusive, Craftsman power tools - at least the handheld ones - can�t stand up to hard daily use.

Re: Old Issue?

#6

Re: Old Issue?

Marv....... Northern California Lake Co.

>Did Sears/Craftsman ever build anything? Is there a Craftsman factory somewhere?

Everything falls within a certain spectrum. The worst on the left and the best on the right with everything else in between.

I've seen lower quality than Craftsman stuff. I'd put Craftsman a little left of center.

Marv

Re: Old Issue?

#7

Re: Old Issue?

Tom MacGregor

>There are better power tools than Craftsman out there, and some are useless junk, but let's give credit where it's due. I've done a lot of work getting by with Craftsman tools until I could afford to upgrade. My first big (at the time) tool purchase over 30 years ago was a 10" Craftsman tablesaw with a ribbed aluminum top. I had to work around its deficiencies more than once, but I learned a lot with that saw and used it to make my first kitchen full of custom cabinets from scratch. I replaced it 8 years ago with their top of the line $1000+ fancy fence cast iron model and am happy with it - acknowledging that I don't have to make my living with it. Of course getting the saw and a 15 speed mountain bike for $100 at an estate sale helped sweeten the deal, too...

Re: Old Issue?

#8

Re: Old Issue?

Victor Parisian

>"I've seen lower quality than Craftsman stuff."

If anyone else on this board ever acquired "tools" from Harbor Freight or similar outlet, they would agree with you without reservation. Craftsman tools are pretty darned good form most people.

Regards,

Victor - in Hot and Humid Houston

Re: Old Issue?

#9

Some of their older "industrial" stuff was

Bill Houghton, Sebastopol, CA

>pretty decent.

I've got one of their aluminum-bodied* "industrial" sidewinder skilsaws that has served me well for six or seven years of work on the house and that I'm still using even with wobbly bearings until I get some time to do tool maintenance, $10 at a garage sale and older than either of my boys.

Would I buy a power tool from Sears new? Probably not, although some of their tools have been ranking OK in the magazine comparos. But they're not all trash.

*It's got a sandcast finish, which is touted on the tool label as "no-glare." This tool dates from near the end of the polished-aluminum-body era, and Sears clearly figured out that polishing added a step, and then figured out how to market their cost savings as a feature. It does in fact make sense on a tool that will be used on a jobsite, often in full sun; but it's still kind of amusing.

Re: Old Issue?

#10

Re: Some of their older "industrial" stuff was

Marv....... Northern California Lake Co.

>Hi Bill,

I still have a 3/8 Craftsman variable speed drill motor that I have had for over 35 years. It is the full bodied aluminum type you mention. It came to pass, a few years later the danger of electrical shock with the all metal housings was the reason for going to the plastic housings, at least that was the story. No doubt a cost savings also.

I have a Craftsman 12" tablesaw with the blade attached directly to the motor shaft. I bought it at a Sears parking lot sale in Mountain View down in the Bay Area about the same time I bought the drill motor. I paid only $300 for it. The Uni-fence I put on it 15 years later cost more than the saw. The bearings in the motor are starting to talk me now. They are saying they are old and tired.

I have it on wheels so I can move it around if need be. Problem is, everytime I want to move it, I need to spend a couple days cleaning the sawdust and crap from around it. It hasn't been moved for about three years.

Now days when we go to Sears, we can choose from most other popular brands when it comes to drill motors and other kinds of hand-held tools.

Harbor Freight on Piner Road is one of my regular stops when I make it to Santa Rosa. I buy my small things from them such as sandpaper and packaged assortment of screws and other fasteners, etc. I steer away from the larger machines such as drill presses and the like.

Post Tool across the street from Harbor Freight used to be a good tool stop for me until they sold out and eliminated all the open box odds and ends that I loved to sort through. Got a lot of good buys there.

Same thing with Santa Rosa Tool farther down the street. That used to be a good place to do business, but now with the new owners I don't buy much there anymore. I bought a Jet bandsaw and a Jet metal lathe from them.

When I was in business for myself, I did a lot of business with Hewlett Packard that used to be near Santa Rosa Tool.

Marv