Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Porter Cable 557 Plate Joiner problems-Help.

Posts

Porter Cable 557 Plate Joiner problems-Help.

#1

Porter Cable 557 Plate Joiner problems-Help.

Ray Carson, New Jersey

>Hello,

I own a Porter Cable 557, type 2, plate joiner and it gets used quite frequently. Recently I've been having some issues with getting the blade cover screws out to change blades. Also, the allen screw that holds the retainer and blade on has been a real knuckle buster.

Well, the other night I went to change the blade from the 4 inch to the 2 inch and one of the cover screws stripped out. After tapping it and using a screw extractor it came free. About 20 minutes on that process.

Then I tried to get the allen screw out to change the blade. Scraped up three of my knuckles and completely rounded out the allen wrench hole. Needless to say that a few explicitives followed as did the wife down the basement steps.

Anyway, now I have to replace the plate cover screw and try and figure how to get the allen screw out without ruining the joiner.

My feeling is that the plate cover screws are steel and the housing is Magnesium or something and they aren't playing nice together. The allen screw appears to be tightening itself, kind of the way a table saw blade does. You all know how the spinning of the blade in conjunction with the threads helps to keep the nut tight....

Question:

Has anyone else had these problems with this power tool?

I'd appreciate your thoughts and suggestions.

Thanks,

Ray

Re: Porter Cable 557 Plate Joiner problems-Help.

#2

Re: Porter Cable 557 Plate Joiner problems-Help.

Chuck W

>would it be possible to grind a slot in the allen head to try and use a flat screwdriver?

Re: Porter Cable 557 Plate Joiner problems-Help.

#3

Re: Porter Cable 557 Plate Joiner problems-Help.

Bob Entwisle in NJ

>Hi Ray,

I have the same machine and the first time I opened it up, I noticed that the screws are a bit tight in the housing. For steel screws into soft stuff like aluminum I'm a strong believer in anti seize compound.

I just opened mine up to take a look. I noticed that the socket head screw that holds the blade on has a notch on the bottom 1/8" similar to self tapping screws, if it�s not carefully threaded back into the hole, I bet it would be easy to mess up the threads on the shaft and get the screw jammed tight.

I would try drilling it out if you can�t get it to move with the hex key.

I measured the screw and it is 9/16" long. The depth into the shaft including the blade and washer is 1 inch, so lots of clearance below the screw. Since it's a socket head you have a good center to start drilling from. I think about 3/16" max diameter drill bit, maybe a hair less to be safe. If you have a set of left hand drill bits they often grab and spin the broken screw out. I'd be hesitant to try and cut a slot on the screw as it's a flat head, so you don't have a great angle of attack to cut the slot.

Good luck and let us know how you make out with it.

Bob

Re: Porter Cable 557 Plate Joiner problems-Help.

#4

Re: Porter Cable 557 Plate Joiner problems-Help.

Dan Donaldson

>After you get the screws out, you might want to think about putting anti-seize on them before putting in the new ones. That stuff helps a lot in the cases of dissimilar metals.

Re: Porter Cable 557 Plate Joiner problems-Help.

#5

Re: Porter Cable 557 Plate Joiner problems-Help.

Don Evans

>The new style "easy outs" that came out 3 or 4 years ago are well worth the price. If you don't have a set get them and use them.

The difference:

the old ones have a twisted shaft that you have to predrill hole for them to work.

the new ones don't have the twisted shaft but instead look like a counter sink bit, but the only grab when turned left hand. They don't need a predrilled hole most of the time. the bit and grab much better than the old style. usually there are 3 in a set.

Don

Re: Porter Cable 557 Plate Joiner problems-Help.

#6

Re: PC 557 , Left hand drill bits. *LINK*

Bob Entwisle in NJ

>I poked around and found this link, no experience with this company but seems like a good price.

These things are worth their weight in gold when you need to drill out a screw!

Bob


http://www.cvfsupplycompany.com/drbi13pcleha.html

Re: Porter Cable 557 Plate Joiner problems-Help.

#7

Re: PC 557 Plate Joiner problem - Fixed.

Ray Carson - Lawrenceville, NJ

>After about an hour last night, I finally managed to free the seized allen screw. What worked you ask?

I cut a slot across the screw as Chuck had suggested. Actually it was funny because I didn't read his post until this morning after freeing it up last night. Brilliant minds think alike Chuck. :-) It didn't work. I cut the slot very carefully with a dremel tool and I think the heat from cutting maybe softened the surrounding metal. The flat screwdriver "cammed" out.

What worked was slightly tapping the top of the screw to shock it and then I used a set of channel locks on the retaining washer which has two flat sides ground into it. Finally came free.

I've since called PC and got new screws free of charge. Apparently I'm not the only person who has had this issue.

Before replacing the screws I will be applying some anti-seize stuff as some have suggested so this doesn't happen again.

Thanks everyone.

Ray