Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Chair upholstery

Posts

Chair upholstery

#1

Chair upholstery

Thomas S Stockton

>Here is a article on chair upholstery. I also sent it on to the articles section

How I upholster a chair seat.

The first step is to make a frame, I use 3/4� baltic birch plywood. I first cut the outside shape on the tablesaw notching the corners a bandsaw. I then cut out the center using a jigsaw, the rails end up being about 1 1/2� wide. The frame is made about a 1/4� undersize on each edge to allow for the fabric. I then round over all the edges of the rails with a 1/4� roundover bit.


img

Re: Chair upholstery

#2

Re: Chair upholstery

Thomas S Stockton

>Next step is to put the jute webbing on the frame. I rough cut the webbing and staple down one edge. The webbing is then stretched and the other end is stapled down. You can buy special stretchers but I�ve found a pair of vice grips works better. The rest of the webbing is done the same way. You want to weave in and out of each other to add stiffness. I use a pneumatic stapler for all my upholstery work.


img

Re: Chair upholstery

#3

Re: Chair upholstery

Thomas S Stockton

>Once the webbing is down the next step is to cut a piece of burlap a little smaller that the seat. This gets put down with spray adhesive and prevents the foam from pinching and wearing out prematurely.


img

Re: Chair upholstery

#4

Re: Chair upholstery

Thomas S Stockton

>I then rough cut a foam seat on the bandsaw. I prefer 1� thick foam. I�m not sure of the density, I go by fell at the upholstery supply store. I don�t like the stuff that is so dense it fells like a pad a backpacker would use and the really light weight stuff is to soft.

The foam is then attached using more spray adhesive. After the glue sits for a couple of minutes I cut the foam to size on the bandsaw. What I do is flip over the seat so the foam is facing down and go around the whole thing following the frame so that the foam is flush. Unless the notches are huge I just leave them square.


img

Re: Chair upholstery

#5

Re: Chair upholstery

Thomas S Stockton

>The next step is to attach fiberfill batting to the seat. This is wrapped around and stapled on the underside, you only need to put staples every 4� or so to hold it in place.

I then trim the excess using a utility knife.


img

Re: Chair upholstery

#6

Re: Chair upholstery

Thomas S Stockton

>Now comes the covering material. I usually use leather but on these chairs the client supplied me with some real nice upholstery fabric that was real forgiving to work with. The hardest part was keeping the pattern straight and centered. It really pays to use covering materials designed for upholstery they are easier to work with and hold up better over time. The worst pattern in my opinion is anything with stripes, it takes a lot of work to keep the lines straight and if they are off even a little they look terrible.

I start at the front edge and place a staple every few inches. I then pull and stretch the fabric and attach it at the back.

I then flip over the seat and see how it looks, if it isn�t right I rip out the staples I need to and adjust it so it works. I then do the sides the same way. After the sides are done and everything looks good I do the corners. Corners are tricky, what I do is not put a staple within a couple of inches of it and then pull the fabric at the corner towards me bisecting the angle and put a staple there. I can then worm my way out stretching and stapling as I go. The reason corners are tricky is because each covering material behaves a little different and you need to adjust your technique as you go. The thing I try to remember is that on a slip seat all you see is the top and a little bit of the edge. So what is on the underside is hidden and eventually covered. You still need to do a good job and make each seat look the same, just some of your problems are hidden.


img

Re: Chair upholstery

#7

Re: Chair upholstery

Thomas S Stockton

>The final step is to put a covering over the underside. I use black cotton fabric. upholstery shops carry material to do this but is seems pretty flimsy to me. One trick I use is to use a sharpie pen to turn the crown of the staples black that I use for this covering. This doesn�t completely hide them but it�s better than shinny staples.


img

Re: Chair upholstery

#8

all done

Thomas S Stockton

>Now I�m done and can have my own version of the Princess and the Pea.


img

Re: Chair upholstery

#9

JL

Thanks for sharing. Recommended seat frames?

JL

>I have to do a quote on a prairie settle sometime soon. This gives me ideas. I can get a local weaver to weave me a suitable cloth.

Re: Chair upholstery

#10

Nice job; great chair

Clint Searl, at the base of Haycock Mtn

>

Re: Chair upholstery

#11

Re: Chair upholstery

Glenn Madsen near San Francisco

>Thank you, sir. That was a good, concise summary.

I took a couple of Adult Ed classes on this stuff, and you covered it MUCH more quickly than they did, and explained a couple of reasons that either I missed, or the teacher did.

And I agree on the stripes. I learned that lesson on wallpaper in the 1970's. :-)

Re: Chair upholstery

#12

Re: Chair upholstery

George@Colonel's Workshop-Havertown PA

>Good Morning Tommy,

Oh, many many times I've gone thru that drill. I did more upholstery work than wood work, but never liked it. You are certainly right about stripes and patterns. Positioning means everything. I preferred patterns even though it took a lot more material to center, and sometimes waste. We differ on the aspect of a webbing stretcher. I couldn't do without mine.

George

Re: Chair upholstery

#13

Re: all done

Howard Norman

>Thanks for the input. It looks like I will be helping a son do a set of six dining room chairs in the not too distant future. Your information will be valuable for that task I am sure.

howard

Re: Chair upholstery

#14

Re: Chair upholstery

Hikmet C. Sakman -- Victoria, BC.,CDN

>Looking good Tom, very good.

Chico...

Re: Chair upholstery

#15

Excellent!

Joanne in Pt. Pleasant, PA

>Thanks for posting this. I've been thinking of trying chairs. This makes it less daunting. How do you attach the seat to the chair frame?

Re: Chair upholstery

#16

Re: Excellent!

Thomas S Stockton

>The seat is attached with screws that go through corner blocks, although it can also be a friction fit on this design and just sit on the corner blocks.

Tom